Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      - 3.4.11. Removal and engine installation
         3.4.11.1. Engine of 2,6 l
         3.4.11.2. 12-klapanny engine of 3,0 l
         3.4.11.3. 24-klapanny engine of 3,0 l
         3.4.11.4. Engine of 3,5 l
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.11.3. 24-klapanny engine of 3,0 l

GENERAL INFORMATION

ORDER OF REMOVAL OF 24-KLAPANNOGO OF THE ENGINE OF 3,0 L

Disconnected units, hoses and wires at dismantle of the 24-klapanny engine of 3,0 l

10. Burn down control systems of the engine
11. Generator socket
12. Joint of a maslookhladitel
13. Accelerator cable
14. Butterfly valve cable
15. Hose of the amplifier of brakes
16. Heater hose
17, 18. Gasoline pipe line
19. Socket of the sensor of pressure of oil
20. Guards
21. Bolt of a support of the engine

Removal

PERFORMANCE ORDER
1. Remove a cowl.
2. Remove the battery and a tray.

3. Remove intermediate draft cruise control. For this purpose execute the following:

  – unscrew a bolt and remove a protective casing of draft;
  – disconnect from draft a butterfly valve cable, a cable of an accelerator and cruise control. Adjusting bolts and nuts do not turn on, only release;
  – unscrew 4 bolts and remove intermediate draft;
  – remove a draft arm, bolts and screws store in a separate package to screw on former places.

4. Lift the car and remove engine and transmission guards.
5. Disconnect weight.
6. Merge liquid from cooling system. Merge oil from transmission and the engine.
7. Disconnect on the engine hoses of a radiator and other hoses of system of cooling.
8. Remove a fan casing.
9. Remove a radiator.
10. Disconnect from collectors exhaust pipes.
11. Remove transmission (see subsection 9.3.6).
12. Remove an air line of the air filter.
13. Remove the pump of the hydraulic booster and take aside, without disconnecting from the highway.
14. Remove a belt of a drive of the generator.
15. Remove the conditioner, without disconnecting from the highway, take aside and fix.
16. Remove a pulley of the pump of system of cooling with the fan.
17. Disconnect from the engine all wires.
18. Unscrew the union of a maslookhladitel.
19. Disconnect a hose of the amplifier of brakes.
20. Disconnect a hose from the leveling chamber and heater hoses in a back part of an inlet collector.
21. Disconnect a return fuel hose.
22. Disconnect a wire of the sensor of pressure.
23. Attach таль the lift and will hang out the engine.
24. Remove guards of support of the engine and unscrew bolts of fastening of support of the engine to a frame.
25. Carefully lift the engine and get from a motor compartment. Establish the engine on supports (not on the pallet).

Installation

PERFORMANCE ORDER
Installation of the engine is carried out upside-down. First of all establish the engine, wrap bolts of support and tighten them with the moment of 44 N of m. Replace laying of an exhaust pipe on a collector, and also a sealing ring of a gasoline pipe line. Bolts of fastening of a pulley of the fan tighten with the moment of 10-12 N of m. Bolts of fastening of a radiator tighten with the moment of 8-11 N of m. Fill in liquid, oil and start the engine. After warming up restore levels of liquids. Repeatedly adjust a zaslonka cable, belts, idling.