Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Major maintenance of the engine
3.4.1. Engine electric equipment
3.4.2. Ignition distributor
+ 3.4.3. Generator
3.4.4. Battery
3.4.5. Starter
3.4.6. Traction relay of a starter
3.4.7. Sensors
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. Cover of a head of the block of cylinders
+ 3.4.13. Rollers and yokes
3.4.14. Thermostat of system of cooling
3.4.15. Inlet collector
3.4.16. Final collector
3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Turbokompressor
3.4.19. Turbonagnetatel
3.4.20. Radiator
3.4.21. Maslookhladitel
3.4.22. Fan
3.4.23. The pump of cooling liquid
+ 3.4.24. Head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. Gear belt and covers
3.4.30. Chain and cover (engine of 2,6 l)
3.4.31. Oil pallet
3.4.32. Oil pump and saylent-rollers (vibrogasitel)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. Back epiploon
3.4.37. Radical bearings
3.4.38. Flywheel
+ 3.4.39. Exhaust system
+ 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
Chain of the engine of 2,6 l
1. Washer
2. Pulley
3. Chain cover
4, 6. Laying
5. Cap
7. Epiploon
8. Uspokoitel V.
9. Uspokoitel A.
10. Uspokoitel S.
11. Small chain
12. An asterisk In
13. Asterisk of the oil pump
14. Zvedzdochka of the left roller
|
15. Plug
16. Natyazhitel
17. Sealant
18. Spring
19. Gear wheel
20. Pin
21. Cam-shaft asterisk
22. Cam-shaft chain
23. Crankshaft asterisk
24. Uspokoitel from a chain tension
25. Uspokoitel from a chain tension
26. Holder of an asterisk |
Adjusting labels of a chain on the engine of 2,6 l
|
|
1, 6. The anodized link
2, 5. Label (pole)
3. Chain
4, 9. Uspokoitel
7. Crankshaft asterisk
8. Natyazhitel
10. Cam-shaft asterisk |
Combination of asterisks and small chain (2,6 l)
|
|
1, 6, 9. Uspokoitel
2. Block of cylinders
3, 8. Label
4, 7. The anodized link
5. Asterisk
10. A cut on X
11. A cut on Y
12. Bolt |
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
2. Merge liquid. |
| 3. Disconnect a hose of a radiator and remove the top casing of the fan. |
| 4. Remove the fan with the coupling and store without breaking working situation. |
| 5. Remove belts of hinged units. |
| 6. Remove a fan pulley from the cooling pump. |
| 7. Disconnect from the cooling pump a heater hose. |
| 8. Unscrew bolts, having paid attention to their arrangement, and remove the cooling pump. |
| 9. Unscrew a bolt and a stripper press a crankshaft pulley. |
| 10. Uncover heads of cylinders. |
| 11. Turn out from a head of cylinders of 2 forward bolts of fastening of a cover of a chain. |
| 12. Turn out bolts of fastening of the pallet, the chains screwed in a cover. |
| 13. Unscrew bolts and uncover, having destroyed consolidation by the sharp tool. If at removal of a cover the forward part of laying of the pallet was damaged, accurately cut out this part aflush with the block of cylinders. |
| 14. Replace a forward epiploon, having accurately got it and having pressed new opravky MD998376–01 or MB990938–01. |
| 15. Establish the piston of the 1st cylinder in VMT of a step of compression (yokes should rock freely within a gap). |
| 16. Remove 3 uspokoitel resting against a chain of the roller of a vibrogasitel, having marked each of fastening bolts. |
| 17. Remove a small chain from the roller of a vibrogasitel and from the oil pump. If the chain does not give in, unscrew bolts and remove asterisks together with a chain. Remove shponka (if are provided). Pay attention to orientation of asterisks. |
| 18. Remove the 1st asterisk of the crankshaft. |
| 19. Fix a wire a plunzher of a natyazhitel in the case of the oil pump. |
| 20. Unscrew a bolt and remove an asterisk of a cam-shaft and a gear wheel of a drive of the distributor of ignition. It is possible to remove also a chain together with crankshaft and cam-shaft asterisks. |
| 21. Remove uspokoitel, keep all bolts and washers in a former order. |
|
Installation
| PERFORMANCE ORDER |
| 1. Believe a chain condition, at detection of worn-out links a chain replace. Replace a worn-out plunzher of a natyazhitel together with a sealant and a spring. Replace uspokoitel if in them deep furrows were formed. At visible wear of teeths replace asterisks |
| 2. Establish the left and right uspokoitel. |
| 3. Dress a chain on crankshaft and cam-shaft asterisks, having combined labels with the anodized links of a chain. Dress an asterisk on the crankshaft, and an asterisk of a cam-shaft fix on the holder. |
| 4. Dress a cam-shaft asterisk, having passed a pin in an opening and tighten a bolt with the moment of 54 N of m. |
| 5. Remove a wire from a natyazhitel and pull a chain. |
| 6. Dress a small chain together with asterisks, having combined labels and links with distinctive coloring (asterisks to establish, without breaking their former arrangement). |
| 7. Dress a gear wheel of Century. |
|
8. Dress a small chain on a crankshaft asterisk. having combined with a label 3 the anodized link. Dress on the roller and the oil pump other asterisks, slightly tighten bolts (1, 2 – to a chain; 3–asterisk installation on the left roller; 4–asterisk installation on a neck of a leading gear wheel of the oil pump). |
|
9. Turn both asterisks of a small chain and the oil pump, expose a place of the greatest weak point in a point of R on an illustration.
|
| 10. Establish uspokoitel of a small chain and adjust the top uspokoitel (In) so that the gap between a chain and an uspokoitel was 0,2–0,8 mm. Tighten a bolt with the moment of 19 N of m. |
| 11. Establish all removed details. At installation of covers check a condition of laying. Cut out a part of remote laying and establish, having greased a joint with hermetic. Tighten bolts of a cover of a chain with the moment of 14 N of m, a crankshaft bolt – 119 N of m, pallet bolts – 5 N of m, forward bolts of a head of cylinders – 19 N of m. After start-up of the engine hear to noise from a chain. If unusual noise are distributed, stop the engine and check installation and a chain tension. Upon termination of adjust belts of a drive of hinged units. |
|
|
|