Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Major maintenance of the engine
3.4.1. Engine electric equipment
3.4.2. Ignition distributor
+ 3.4.3. Generator
3.4.4. Battery
3.4.5. Starter
3.4.6. Traction relay of a starter
3.4.7. Sensors
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. Cover of a head of the block of cylinders
+ 3.4.13. Rollers and yokes
3.4.14. Thermostat of system of cooling
3.4.15. Inlet collector
3.4.16. Final collector
3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Turbokompressor
3.4.19. Turbonagnetatel
3.4.20. Radiator
3.4.21. Maslookhladitel
3.4.22. Fan
3.4.23. The pump of cooling liquid
+ 3.4.24. Head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. Gear belt and covers
3.4.30. Chain and cover (engine of 2,6 l)
3.4.31. Oil pallet
3.4.32. Oil pump and saylent-rollers (vibrogasitel)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. Back epiploon
3.4.37. Radical bearings
3.4.38. Flywheel
+ 3.4.39. Exhaust system
+ 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
ENGINE OF 2,0 L
Prevention
Familiarize with procedure of removal of a gear belt.
The pump of cooling liquid of the engine of 2,0 l
|
1. Casing
2–5. Belts
6. Krylchatka with the coupling
7, 8, 9. Pulleys
10. Top cover
11. Bottom cover
12. Natyazhitel
|
13. Gear belt
14. Hose
15. Branch pipe
16. Pump
17. Laying
18. Ring |
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Establish the piston of the 1st cylinder in VMT of a step of compression. |
| 3. Merge liquid. |
| 4. Remove the top casing of the fan. |
| 5. Remove all belts, having weakened bolts of fastening of the corresponding unit. |
| 6. Remove the fan and the inclusion coupling. |
| 7. Remove a pump pulley. |
| 8. Unscrew bolts and remove from a crankshaft sock pulleys. |
| 9. Remove covers, weaken a natyazhitel and, without breaking crankshaft installation, remove a gear belt, having designated on it a piece of chalk the rotation direction. |
| 10. Disconnect a hose, unscrew bolts and remove the pump. |
| 11. Check a pump condition. At detection of damages of the case or a leak through a control opening the pump replace (to repair is not subject). Clear the demountable plane of the pump. |
|
Installation
| PERFORMANCE ORDER |
|
Installation is carried out upside-down taking into account the following:
– replace laying of the pump and a sealing ring, having moistened it with water or liquid (not oil);
– bolts of fastening of the pump tighten in 2 stages: bolts with marking "4"
– with the moment of 14 N of m, bolts with marking "7" – 24 N of m;
– dress a gear belt so that there was no weak point between asterisks of the crankshaft and the oil pump, or asterisks of the oil pump and a cam-shaft. Release a bolt of a natyazhitel and turn the crankshaft so that the asterisk of a cam-shaft was displaced on 2 teeth from an adjusting label. If the belt on a cam-shaft weakens, choose a weak point, having slightly displaced a natyazhitel down. Tighten bottom, then top bolts of a natyazhitel;
– tighten bolts of covers of a belt with the moment of 11 N of m, a crankshaft bolt – 120 N of m, a small bolt of a pulley – 25 N of m, pulley and krylchatka nuts on the cooling pump – 11 N of m.
|
|
Upon termination of warm up the engine, restore level of liquid and adjust belts.
DIESEL ENGINE
The pump of cooling liquid of a diesel engine
|
1. Pulleys
2. Epiploon
3. Krylchatka
|
4. Perepuskna suited
5. From a radiator
6. To a branch pipe |
Removal and installation
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Merge liquid. |
| 3. Disconnect from the pump a hose. |
| 4. Remove the fan, the coupling and a pulley. |
| 5. Unscrew bolts and remove the pump. |
| 6. Check freedom of rotation of the roller and a condition of consolidations. At detection of damages of the case or a leak through a ventilating opening the pump replace (to repair is not subject). |
| 7. Installation is carried out upside-down. Replace laying. |
|
ENGINE OF 2,4 L
Removal
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Merge liquid. |
| 3. Remove the top casing of the fan. |
| 4. Remove all belts. |
| 5. Disconnect from the pump a hose. |
| 6. Unscrew bolts and remove from a crankshaft sock pulleys. |
| 7. Establish the piston of the 1st cylinder in VMT of a step of compression, remove covers and a gear belt. |
| 8. Unscrew bolts, having paid attention to their arrangement) and remove the pump. |
| 9. Clear the demountable plane of the pump, check its condition. At detection of damages or a leak the pump replace (to repair is not subject). |
|
Installation
| PERFORMANCE ORDER |
|
Installation is carried out upside-down taking into account the following:
– replace laying of the pump and a sealing ring, having moistened it with water or liquid (not oil);
– bolts of fastening of the pump tighten with the moment of 13 N of m;
– establish and pull a gear belt of 2,0 l as it should be specified for the engine (see above). |
|
ENGINE OF 2,6 L
The pump of cooling liquid of the engine of 2,6 l
|
1, 2. Casing
3. Krylchatka with the coupling
4–6. Belts
7. Pulley
|
8. Radiator hose
9. Heater hose
10. Pump
11. Laying |
Removal and installation
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. |
| 2. Merge liquid. |
| 3. Disconnect from the pump a radiator hose. |
| 4. Remove the top casing of the fan. Remove the fan and the coupling, the fan store in working situation. |
| 5. Remove drive belts. |
| 6. Remove a pump pulley. |
| 7. Disconnect from the pump a heater hose. |
| 8. Unscrew bolts, having paid attention to their arrangement, and remove the pump. |
| 9. Clear the demountable plane of the pump, check its condition. At detection of damages or a leak the pump replace (moistening of a control opening) is allowed. |
| 10. Installation is carried out upside-down. Replace laying. Bolts of fastening of the pump tighten with the moment of 21 N of m in stages. Pull belts. |
|
ENGINE OF 3,0 L
Prevention
At pump removal on 6-cylinder engines designate all bolts which establish on the places. The asterisk of the crankshaft is pressed by means of a special stripper.
The pump of cooling liquid of the engine of 3,0 l
|
1. Perepuskna hose
2. Radiator hose
3. Krylchatka with the coupling
4, 7. Laying
|
5. Arm of a natyazhitel
6. Pump
8. Ring |
Removal and installation
| PERFORMANCE ORDER |
| 1. Execute a decompression. For this purpose disconnect the socket in a back part of a fuel tank, start the engine and after its stop switch off ignition. |
| 2. Disconnect the battery from weight. |
| 3. Merge liquid, remove the thermostat, disconnect the top hose of a radiator, perepuskny a hose, remove a fan casing. |
| 4. Remove the fan and the coupling. |
| 5. Remove drive belts. |
| 6. Remove a pump pulley. |
| 7. Remove the pump of the hydraulic booster and arms. Take the pump aside, without disconnecting from the highway. |
| 8. Remove an arm of a natyazhitel. |
| 9. Remove the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix. Remove a compressor arm. |
| 10. Remove a fan arm. |
| 11. Establish the piston of the 1st cylinder in VMT of a step of compression, remove covers, release bolts of a natyazhitel and remove a gear belt, having designated the rotation direction. |
| 12. Unscrew bolts, having paid attention to their arrangement, and remove the pump. |
| 13. Remove a branch pipe and clear the demountable plane of the pump, check its condition. At detection of damages or a leak the pump replace. |
| 14. Installation is carried out upside-down. Replace all removed laying and a sealant. Belts establish and adjust, being guided by the description in appropriate sections. Bolts of fastening of the pump tighten with the moment of 27 N of m. |
|
ENGINE OF 3,5 L
The pump of cooling liquid of the engine of 3,5 l
|
1. Radiator hose
2. Final branch pipe
3, 11. Ring
|
4, 6, 10. Laying
5. Thermostat
7. Transitional station |
Removal and installation
| PERFORMANCE ORDER |
| 1. Execute a decompression. For this purpose disconnect the socket in a back part of a fuel tank, start the engine and after its stop switch off ignition. |
| 2. Disconnect the battery from weight. |
| 3. Merge liquid. |
| 4. Remove a radiator with the top hose and a fan casing. |
| 5. Remove the generator, the battery and a tray. |
| 6. Remove the bottom guards of the engine. |
| 7. Remove the fan, the coupling and a pump pulley. |
| 8. Remove the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix. Remove a compressor arm. |
| 9. Remove the pump of the hydraulic booster and arms. Take the pump aside, without disconnecting from the highway. |
| 10. Remove forward covers and disconnect the socket from the sensor of rotation of the crankshaft. |
| 11. A stripper press a crankshaft pulley. |
12. Remove a gear belt. For this purpose execute the following:
– combine labels on asterisks and on a head of cylinders;
– release a bolt of a natyazhitel and designate on a belt the rotation direction. |
| 13. Remove a natyazhitel, a roller and the lever. |
| 14. Remove from the pump the top branch pipe and the thermostat. |
| 15. Clear the demountable plane of the pump, check its condition. At detection of damages or a leak the pump replace. |
| 16. Installation is carried out upside-down. Replace the removed laying and a sealant. Belts establish and adjust, being guided by the description in appropriate sections. Bolts of fastening of the pump tighten with the moment of 24 N of m in 2–3 stages, being displaced on the periphery. Napressuyte on the crankshaft a pulley by means of the special adaptation. |
|
|
|