Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.6. Traction relay of a starter

GENERAL INFORMATION

Conclusions on the traction relay

M, In and S – conclusions

Check of a course of a gap of a gear wheel of the traction relay

1. Limiter

2. Gear wheel

3. Gap

4. Gear wheel course

Adjusting laying of the traction relay

 

Back cover of a starter

1. Coupling bolts

2. Winding conclusion

3. Back cover of a starter

Check

PERFORMANCE ORDER
1. On the idle relay disconnect the plug on a conclusion of M and concern with a crossing point attached to the battery, S conclusion. If the relay works, conducting or the ignition lock is faulty. Otherwise the relay replace. It is possible also to ask to include the assistant a starter (having disconnected a coil wire on the distributor) and to measure tension between M and Century conclusions.
2. If on a working starter tension on a conclusion In close to tension of the battery, and on a conclusion In strongly differs, the relay replace.

Removal and installation

PERFORMANCE ORDER
1. Remove a starter.
2. Disconnect the plug on the M conclusion.
3. Unscrew screws, unhook a plunzher from a fork and remove the traction relay, without allowing loss of laying. Measure thickness of laying and define their number.
4. Establish laying and the relay, tighten screws.
5. Check a gap between a gear wheel and the limiter, having connected to conclusions of S and relay M (+) and (-) battery poles for the period of no more than 10 pages. On a starter with a reducer check a gear wheel course. The gap (a gear wheel course) should be 0,5–2,0 mm. If necessary correct selection of laying.
6. Establish a starter.

Replacement of brushes

Check and replacement of brushes of a starter


1. The bottom edge of a brand is the line of limiting wear

2. Brush

3. Soldering

4. The party with a brand

5. Wire

PERFORMANCE ORDER
1. On the removed starter disconnect the plug M, unscrew coupling bolts and remove a back cover.
2. Raise springs and get brushes, remove a shchetkoderzhatel from a back cover.
3. Check brushes. If wear reaches a firm brand, brushes replace.
4. For replacement crush worn-out brushes and carefully smooth out a brush wire on 6 mm. Insert a wire into a new brush from outside where there is no brand and is accurate пропаяйте, without allowing a solder effluence from the opposite side.
5. Further execute assembly upside-down.