Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.2. Ignition distributor

GENERAL INFORMATION

Distributor of ignition of engines 2,0 and 2,6 of l

1. Tip cover
2. Cover
3. Piece of coal
4. Begunok
5. Wire
6. A wire on weight
7. Ignition block
8, 24 Pin
9. Rotor
10. Plate
11. A vacuum regulator with 2
diaphragms
12. A vacuum regulator with 1 diaphragm
13. Rotor of a centrifugal regulator
14. Spring emphasis
15. Spring
16. Counterbalances
17. Roller
18. Epiploon
19. Sealant
20. Shaft
21. Ring
22. Washer
23. Gear wheel

Distributor of ignition of the engine of 2,4 l

1. Cover
2. Sealant
3. Piece of coal
4. Begunok
5. Wire
6. Ring
7. Case

Distributor of ignition of the 12-klapanny engine 3,0

1. Cover
2. Ring
3. Piece of coal
4. Begunok
5. Ring
6. Case

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Disconnect latches (or unscrew screws) and uncover the distributor together with wires, take aside.
3. Designate position of the distributor on the block of cylinders.
4. Designate and disconnect a hose from a vacuum regulator.
5. Disconnect from the distributor the socket.
6. Designate situation a begunka concerning the distributor.
7. Unscrew a nut and get the distributor. Pay attention to the provorachivaniye direction a begunka at removal the distributor, designate situation a begunka on the removed distributor.
8. Remove a sealant from a distributor shaft.

Installation

Prevention

The crankshaft at the removed distributor was not turned.


PERFORMANCE ORDER
1. Installation is carried out upside-down. Replace a sealant. At installation will expose a begunok, in situation designated after distributor removal, carefully enter the distributor into the block of cylinders, slightly turn the roller, having entered drive gear wheels into gearing, and having pressed, put the distributor into place, having combined labels on the block of cylinders and the distributor case.

Prevention

The crankshaft was turned at the removed distributor


2. Expose the piston of the 1st cylinder in VMT of a step of compression. For this purpose turn the crankshaft clockwise before label combination on a pulley or an uspokoitel with inflow on the block of cylinders. Remove a klapanny cover and check springs of valves of the 1st cylinder. If both springs or at least one are compressed, turn the crankshaft on 1 turn. If yokes rock, the piston of the 1st cylinder is in VMT of a step of compression.
3. Turn the distributor roller so that labels on a gear wheel and a distributor shaft (метки:1 – on a gear wheel, 2 – on a distributor shaft) coincided.
4. Enter the distributor into the block of cylinders, slightly turn the roller, having entered drive gear wheels into gearing, and put the distributor into place. If the begunok was not combined with a conclusion for a candle of the 1st cylinder, submit the distributor back. tighten the roller and again put наместо.
5. Combine labels on the block of cylinders and the distributor case, tighten a bolt (nut) and establish all removed details.