Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.37. Radical bearings

GENERAL INFORMATION

Indicator installation for check axial люфта the crankshaft


Indicator installation for check of palpation of radical necks of the crankshaft

 

Radical loose leaves

1, 3. The flute is absent

2. With a flute

4. Average loose leaves of N 3

5. Bottom loose leaves of N 1, 2, 4 and 5

6. Top loose leaves of N 1, 2, 4 and 5

Order of a tightening of covers of radical bearings on 4-cylinder engines


Order of a tightening of covers of radical bearings on 6-cylinder engines

1. Crankshaft
2. Forward arrow
3. Cover
4. Bolt

Removal

PERFORMANCE ORDER
1. Remove the engine and transmission.
2. Remove a head of cylinders, gear belts, the pallet, the oil pump, a flywheel, and a back epiploon.
3. Overturn the engine and check axial люфт the crankshaft.
4. Unscrew bolts of covers of radical bearings and remove covers, previously having marked their orientation and belonging to this cylinder (on a part of covers the arrow directed to a forward part of the engine) is provided.
5. Remove the crankshaft and radical loose leaves which store individually.
6. Wash out a cranked shaft solvent and dry.

Cleaning and check

PERFORMANCE ORDER
1. Check uniformity of wear of radical and shatunny necks, existence on them задиров, cracks or a local erosion.
2. Check uniformity of wear of necks. If wear non-uniform, necks of the crankshaft follows перешлифовать in car-care center and to replace all bearings repair.
3. Measure by a micrometer diameter of radical and shatunny necks, compare result to standard value. Check ovality (1) and a konusnost (2) radical and shatunny necks, having measured their diameter in several points on a circle and along a neck.
4. Check a surface of radical loose leaves. At any signs of a doubtful condition or if axial люфт norms are higher – loose leaves replace. When dismantling engine loose leaves are recommended to be changed.

Installation

PERFORMANCE ORDER
1. Check gaps in radical bearings on thickness of the crushed plastic calibre. For this purpose place loose leaves (see fig. Radical loose leaves), establish the crankshaft and tighten bolts of covers with loose leaves then accurately remove covers. Oil presence on necks and a crankshaft provorachivaniye at measurements are not allowed.
2. If gaps do not correspond to norm, loose leaves replace. If replacement does not lead to a normal gap, прошлифуйте the crankshaft.
3. Check crankshaft palpation.
4. At final assembly grease necks of the crankshaft and check arrangement of loose leaves. Establish covers (1 – oriyentatsionny shooters, 2 – cover number), it is correct them сориентировав on available labels or put when dismantling and tighten bolts. General order of an inhaling: an average cover – 2nd – 4th – a lobby – back.
5. Without tightening, establish epiploons, a maslopriyemnik and the pallet.