Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Major maintenance of the engine
3.4.1. Engine electric equipment
3.4.2. Ignition distributor
+ 3.4.3. Generator
3.4.4. Battery
3.4.5. Starter
3.4.6. Traction relay of a starter
3.4.7. Sensors
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. Cover of a head of the block of cylinders
+ 3.4.13. Rollers and yokes
3.4.14. Thermostat of system of cooling
3.4.15. Inlet collector
3.4.16. Final collector
3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Turbokompressor
3.4.19. Turbonagnetatel
3.4.20. Radiator
3.4.21. Maslookhladitel
3.4.22. Fan
3.4.23. The pump of cooling liquid
+ 3.4.24. Head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. Gear belt and covers
3.4.30. Chain and cover (engine of 2,6 l)
3.4.31. Oil pallet
3.4.32. Oil pump and saylent-rollers (vibrogasitel)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. Back epiploon
3.4.37. Radical bearings
3.4.38. Flywheel
+ 3.4.39. Exhaust system
+ 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
ENGINES 2,0 AND 2,6 L
Final collector of the engine 2,0 and 2,6 of l
|
1. Filter
2. Air offtake
3, 4. Branch pipe
5. Arm
6. Cover
7. Oxygen sensor
|
8. Samopodzhimny nut
9. Flange of an exhaust pipe
10, 13. Laying
11. Hook
12. Collector
|
Removal and installation
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. Remove the air filter. |
|
2. Disconnect from a collector an exhaust pipe (if necessary lift the car and unscrew bolts from below). |
|
3. Disconnect an air line, a mass wire and a hose. Remove an arm of the valve and a collector cover. |
|
4. Grease nuts of a collector with getting liquid. Turn out the oxygen sensor. Unscrew nuts and remove a collector with the yazychkovy valve and a branch pipe. |
| 5. Clear the demountable planes of a collector and a head of cylinders. |
|
6. Installation is carried out upside-down. Replace laying, nuts of a collector and the damaged hairpins, having turned out them by means of 2 zakontrenny nuts. Tighten all connections with the moments specified an illustrations for the engine of 2,6 l. |
|
ENGINES OF 2,4 L
Final collector of the engine of 2,4 l
|
1. Cover
2, 5. Laying
|
3. Oxygen sensor
4. Collector |
Removal and installation
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight. Remove the air filter. |
| 2. Uncover a collector. |
| 3. Lift a front of the car and disconnect from a collector an exhaust pipe. |
| 4. Turn out the sensor of oxygen and disconnect a wire on weight. |
| 5. Unscrew nuts and remove a collector. |
| 6. Installation is carried out upside-down. Replace laying. Tighten all connections by the demanded moments. |
|
12-KLAPANNY ENGINE OF 3,0 L
Final collector of the 12-klapanny engine of 3,0 l
|
1. Oxygen sensors
2, 3. Exhaust pipes
4, 10, 17. Laying
5. Air line
6, 13. Guard
7. Hook
|
8. Generator arm
9, 16. Collector
11, 12. Tube and laying
14. Rack of the leveling chamber
15. Arm |
Removal and installation (the left collector)
| PERFORMANCE ORDER |
| 1. Remove the battery and a tray. |
| 2. Disconnect from a collector exhaust pipes and fix them a wire. |
| 3. Remove a thermal guard of a collector. |
| 4. Disconnect a retsirkulyatsiya tube with laying from both parties. |
| 5. Remove a rack of an inlet collector with an arm. |
| 6. Unscrew nuts and remove a collector. |
| 7. Installation is carried out upside-down. Replace all laying. Tighten all connections by the demanded moments. |
|
Removal and installation (the right collector)
| PERFORMANCE ORDER |
| 1. Disconnect weight. Remove an air line. |
| 2. Disconnect from a collector exhaust pipes and fix them a wire. |
| 3. Remove from a collector a thermal guard, the right hook and a generator prop. |
| 4. Unscrew nuts and remove a collector. |
| 5. Check the collector plane. A collector with cracks and with the sdeformirovanny plane (a deviation from calibre over 0,3 mm) replace. |
| 6. Installation is carried out upside-down. Replace all laying. Tighten all connections by the demanded moments. |
|
24-KLAPANNY ENGINE OF 3,0 L AND ENGINE OF 3,5 L
Final collector of the 24-klapanny engine of 3,0 l
|
1. Guard
2. Collector right
|
3, 6. Laying
5. Collector left |
Final collector of the klapanny engine of 3,5 l
|
1. Retsirkulyatsiya tube
2, 5, 8. Laying
3, 6. Guards
|
4. Collector right
5. Collector left |
Removal and installation (the left collector)
| PERFORMANCE ORDER |
| 1. Remove the battery and a tray. |
| 2. Disconnect from a collector exhaust pipes and fix them a wire. |
| 3. Remove a thermal guard of a collector. |
| 4. Unscrew nuts and remove a collector. |
| 5. Check a collector condition. A collector with cracks and with the sdeformirovanny plane (a deviation from calibre over 0,3 mm) replace. |
| 6. Installation is carried out upside-down. Replace all laying. Tighten all connections by the demanded moments. |
|
Removal and installation (the right collector)
| PERFORMANCE ORDER |
| 1. Disconnect weight. Remove an air line. |
| 2. Disconnect from a collector exhaust pipes and fix them a wire. |
| 3. Remove from a collector a thermal guard. |
| 4. Unscrew nuts and remove a collector and laying. |
| 5. Check the collector plane. A collector with cracks and with the sdeformirovanny plane (a deviation from calibre over 0,3 mm) replace. |
| 6. Installation is carried out upside-down. Replace all laying. Tighten all connections by the demanded moments. |
|
|
|