Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.38. Flywheel

GENERAL INFORMATION

Prevention

The casing of coupling is balanced together with a press disk. These details change in pair.


Flywheel and leading disk

1. Flywheel
2. Transitional a flange And (on and/m with automatic transmission)
3. Leading disk
4. Transitional a flange In
5. Epiploon

Removal and installation

PERFORMANCE ORDER
1. Remove transmission and coupling.
2. On cars with the engine of 2,0 l on the hydrotransformer the gear wreath is provided, remove the hydrotransformer and check a wreath condition. On all and/m (except and/m with the engine of 2,0 l) unscrew bolts of fastening of a transitional flange, a leading disk and the plug to the crankshaft and remove a disk.
3. On cars from a manual transmission designate the provision of a flywheel, unscrew bolts in a diagonal order and remove a flywheel.
4. Replace a flywheel conducting a disk or the hydrotransformer at detection on them of damages or wear tracks.
5. Establish a flywheel conducting a disk, having combined the labels put at dismantling. The hydrotransformer is established on transmission (not on the engine). Tighten bolts with the moment of 133 N of m on 4-cylinder engines or 74 N of m on 6-cylinder engines.

Gear wreath

At defects of a gear wreath the hydrotransformer replace.

At damage of a wreath of a flywheel it is recommended to replace a flywheel. Replacement of a gear wreath is allowed. For this purpose it is necessary to remove an old wreath and to heat up a new wreath to 300 ° With and напрессовать on a flywheel.