Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.31. Oil pallet

GENERAL INFORMATION

Hermetic drawing on the pallet of V6 engines

1. Drawing near an opening under a bolt
2. To a belt
3. Hermetic
4. Flute

Hermetic drawing on the plane of the pallet of 4-cylinder engines

1. Hermetic
2. Flute
3. an opening under a bolt

Prevention

For performance of this procedure it is required to hang out the engine for what the lift is necessary. Podpiraniye of the engine from below is forbidden. When posting the engine disconnect all wires and hoses, being guided by the description of dismantle of the engine.


On the 24-klapanny engine of 3,0 l and the engine of 3,5 l pallet 2-section. The lower part is made of an aluminum alloy. Bolts of the top section come into a transmission case.

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight. Merge oil and wrap a stopper.
2. Unscrew pallet bolts, having paid attention to their arrangement.
3. Remove the pallet, having opened consolidation by hermetic by special drift МВ998727 and having knocked on corners with a rubber kiyanka. On a small part of cars the pallet is established on laying.
4. Remove a maslopriyemnik. Clear the demountable planes of the pallet, wash out a maslopriyemnik.

Installation

PERFORMANCE ORDER
1. Establish the pallet upside-down.
2. Replace laying of a maslopriyemnik and tighten a bolt with the moment of 18 N of m.
3. Put MZ 100168 hermetic (or equivalent) on the pallet plane, being guided by an illustration.
4. Tighten pallet bolts evenly with the moment of 7 N of m (or in that order on V6 engines).