Mitsubisi Padzhero + 1.1. Dashboard and control units + 2. Maintenance - 3. Engines 3.1. Candles 3.2. Check of wires + 3.3. Ignition system - 3.4. Major maintenance of the engine 3.4.1. Engine electric equipment 3.4.2. Ignition distributor + 3.4.3. Generator 3.4.4. Battery 3.4.5. Starter 3.4.6. Traction relay of a starter 3.4.7. Sensors + 3.4.8. Instructions on service and engine repair 3.4.9. Compression check in cylinders of engines 3.4.10. Specifications of engines + 3.4.11. Removal and engine installation 3.4.12. Cover of a head of the block of cylinders + 3.4.13. Rollers and yokes 3.4.14. Thermostat of system of cooling 3.4.15. Inlet collector 3.4.16. Final collector 3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging) 3.4.18. Turbokompressor 3.4.19. Turbonagnetatel 3.4.20. Radiator 3.4.21. Maslookhladitel 3.4.22. Fan 3.4.23. The pump of cooling liquid + 3.4.24. Head of cylinders 3.4.25. Valves and springs 3.4.26. Saddles 3.4.27. Replacement of directing plugs 3.4.28. Hydropushers + 3.4.29. Gear belt and covers 3.4.30. Chain and cover (engine of 2,6 l) 3.4.31. Oil pallet 3.4.32. Oil pump and saylent-rollers (vibrogasitel) 3.4.33. Cam-shafts and support 3.4.34. Check of a condition of a cam-shaft + 3.4.35. Pistons and rods 3.4.36. Back epiploon 3.4.37. Radical bearings 3.4.38. Flywheel + 3.4.39. Exhaust system + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l + 4. Cooling system + 5. Greasing system + 6. Power supply system + 7. Release system + 8. Fuel system + 9. Running gear + 10. Suspension bracket and steering + 11. Brake system + 12. Body + 13. Electric equipment + 14. Electroschemes
|
Oil pump and rollers of vibrogasitel (2,0 and 2,4 l)
1. Forward bearing 2. Back bearing right 3. Back bearing left 4. Left roller 5, 14, 25. Laying 6. Mesh filter 7, 8, 11, 17. Bolts 9. Forward casing assembled 10. Epiploon 12. Cap 13, 18. Arm of the oil filter
|
15. Spring 16. Reduktsionny valve 19. Oil filter 20. Sensor of emergency pressure of oil (Tredia) 21. Sensor указатедя pressure of oil (Corona) 22. Leading gear wheel oil наоса 23. A conducted gear wheel 24. Cover 26. Right roller |
Oil pump and rollers vibrogasitel (diesel engine)
1. Drain stopper 2, 4, 11. laying 3, 6, 7, 9, 16, 17. Bolt 5. Pallet 8. Maslopriyemnik 10. Top forward cover
|
12. Epiploon 13. Left roller 14. Cap 15. Ring 18. Bottom cover assembled |
Bottom cover assembled 1. Bolt 2. Cover of a gear wheel of the roller 3. A conducted gear wheel 4. Leading gear wheel 5. Screw 6. Cover of the oil pump 7, 8. Gear wheels of the oil pump 9. Cap 10. Laying 11. Spring
|
12. Valve 13. Epiploon 14. Bottom cover 19. Laying 20. Forward epiploon 21. Leading roller of the oil pump 22. Right roller of a vibrogasitel 23. Oil filter |
Prevention
Rollers – vibrogasitel on V6 engines are absent.
ENGINES 2,0 AND 2,4 L
Removal
PERFORMANCE ORDER |
1. Disconnect the battery from weight. |
2. Remove gear belts (see subsection 3.4.29). |
3. Merge oil and remove the oil filter. |
4. Remove the pallet and a maslopriyemnik. |
5. Remove a cap and fix the left roller, having inserted a screw-driver in diameter of 8 mm and length not less than 60 mm. |
6. Release a bolt of the right roller and remove V.Pri neobkhodimosti's natyazhitel remove an asterisk of a belt of the roller. |
7. Unscrew bolts, having paid attention to their arrangement, and remove a forward casing and laying. |
8. Remove a screw-driver and get rollers. |
|
9. Uncover the oil pump and get gear wheels. |
10. Check a condition of gear wheels and the pump planes, replace worn-out details. Clean oil channels. Carefully check a condition of omental consolidations in a forward cover, if necessary replace. Check existence on rollers of development and traces прихвата. |
|
Installation
PERFORMANCE ORDER |
1. Check wear of a plunzher of the reduktsionny valve. Establish in a forward cover, having combined labels. |
2. Grease and establish pump gear wheels into place, having combined labels. |
3. Establish a cover of the pump and tighten bolts with the moment of 21 N of m.
|
|
4. Carefully establish rollers, without having damaged bearings (1–cap; 2–screw-driver). |
5. Dress on the crankshaft an opravka of MD 998285-01. |
6. Establish new laying, establish a forward cover and tighten bolts. |
7. Fix the left roller a screw-driver, tighten a bolt with the moment of 35 N of m. |
|
8. Establish a filter arm, tighten cover and arm bolts with the moment of 23 N of m 9 (1 – a cap).
|
9. Dress on the left shaft a cap. |
10. Collect the reduktsionny valve, tighten a cap with the moment of 45 N of m. |
11. Establish a maslopriyemnik, the pallet and the oil filter.
|
12. Establish asterisks, gear belts and adjust their tension (see subsection 3.4.29). |
|
DIESEL ENGINE
Removal
PERFORMANCE ORDER |
1. Lift a front of the car and merge oil. |
2. Remove the pallet.
|
3. Remove all belts, the top cover of a belt and establish the piston of the 1st cylinder in VMT of a step of compression |
4. Remove asterisks and a gear belt (see subsection 3.4.29) and check a belt condition. If necessary remove a small belt of a drive of the roller. |
5. Remove the top forward cover and remove an epiploon (is subject to replacement). |
6. Designate a relative positioning of gear wheels of the pump. |
7. Remove all details of the oil pump and check their condition. Worn-out details replace.
|
|
Installation
Press fitting of a forward epiploon
|
1. Crankshaft 2. Epiploon 3. Bottom cover 4. Drive of the oil pump 5. Opravka |
PERFORMANCE ORDER |
1. Get and check rollers. |
2. Grease and establish rollers, tighten bolts with the moment of 5 N of m. |
3. Grease and establish pump gear wheels into place, having combined labels. |
4. Establish a cover of the oil pump, tighten bolts with the moment of 22 N of m. |
5. Dress on the crankshaft an opravka of MD 998393.
|
6. Establish new laying, establish a forward cover and tighten bolts. Remove an opravka. |
7. Establish the bottom cover. Replace an epiploon. |
8. Establish all removed details upside-down. Establish asterisks, gear belts and adjust their tension (see subsection 3.4.29). |
|
ENGINE OF 2,6 L
Removal
PERFORMANCE ORDER |
1. Remove both chains and asterisks (see subsection 3.4.30). |
2. Merge oil and remove the filter.
|
3. Disconnect on an arm hoses of the perepuskny valve and a maslookhladitel. |
4. Unscrew a bolt and a nut and remove an arm and sealing rings. |
5. Remove the pallet and a maslopriyemnik, remove laying.
|
6. Remove details of the reduktsionny valve, unscrew bolts and remove the case of the oil pump.
|
7. Get pump gear wheels, remove a shponka from the roller of a vibrogasitel. |
8. Uncover the pump with laying. |
9. If necessary remove the left roller. For this purpose screw 2 bolts М8 in carving openings of a flange and wrapping bolts, выпрессуйте an emphasis. If necessary remove the right roller. |
|
Installation
PERFORMANCE ORDER |
1. Check a condition of the demountable planes of a cover of the pump and in a forward cover of the engine. Check a face gap of gear wheels. If the gap exceeds 0,15 mm, replace gear wheels and (or) the case. Clean oil channels. Check development existence on rollers.
|
2. Replace all laying and a sealant. |
|
3. Before installation grease necks of rollers (1 – a greasing place). |
|
4. An emphasis of the roller establish on directing hairpins М6 in length of 50 mm then remove hairpins and tighten emphasis bolts with the moment of 11 N of m (1–ring; 2–left roller; 3–block of cylinders; 4–hairpin М6; 5–emphasis). |
|
5. At assembly of the pump combine labels of gear wheels and fill in about 10 cubic see oils. |
6. Tighten bolts of a cover of the pump with the moment of 11 N of m, big bolts of the case the pump – 65 N of m, small bolts and screws of-10 N of m. a cap reduktsionny the valve – 10 N of m. |
|
ENGINES 3,0 AND 3,5 L
Removal
PERFORMANCE ORDER |
1. Disconnect the battery from weight. |
2. Remove a masloukazatel. |
3. Lift a car front. |
4. Remove a gear belt (see subsection 3.4.29). |
5. Merge oil, remove the pallet and a maslopriyemnik.
|
6. Unscrew bolts and remove the oil pump, having paid attention to an arrangement of bolts. |
|
Installation
PERFORMANCE ORDER |
1. Installation is carried out upside-down |
2. Replace laying and a crankshaft epiploon. |
|
3. Before assembly fill the pump with technical vaseline, or fill in oil. Tighten pump bolts with the moment of 15 N of m. |
|
|
|