Mitsubisi Padzhero + 1.1. Dashboard and control units + 2. Maintenance - 3. Engines 3.1. Candles 3.2. Check of wires + 3.3. Ignition system - 3.4. Major maintenance of the engine 3.4.1. Engine electric equipment 3.4.2. Ignition distributor + 3.4.3. Generator 3.4.4. Battery 3.4.5. Starter 3.4.6. Traction relay of a starter 3.4.7. Sensors + 3.4.8. Instructions on service and engine repair 3.4.9. Compression check in cylinders of engines 3.4.10. Specifications of engines + 3.4.11. Removal and engine installation 3.4.12. Cover of a head of the block of cylinders + 3.4.13. Rollers and yokes 3.4.14. Thermostat of system of cooling 3.4.15. Inlet collector 3.4.16. Final collector 3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging) 3.4.18. Turbokompressor 3.4.19. Turbonagnetatel 3.4.20. Radiator 3.4.21. Maslookhladitel 3.4.22. Fan 3.4.23. The pump of cooling liquid + 3.4.24. Head of cylinders 3.4.25. Valves and springs 3.4.26. Saddles 3.4.27. Replacement of directing plugs 3.4.28. Hydropushers + 3.4.29. Gear belt and covers 3.4.30. Chain and cover (engine of 2,6 l) 3.4.31. Oil pallet 3.4.32. Oil pump and saylent-rollers (vibrogasitel) 3.4.33. Cam-shafts and support 3.4.34. Check of a condition of a cam-shaft + 3.4.35. Pistons and rods 3.4.36. Back epiploon 3.4.37. Radical bearings 3.4.38. Flywheel + 3.4.39. Exhaust system + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l + 4. Cooling system + 5. Greasing system + 6. Power supply system + 7. Release system + 8. Fuel system + 9. Running gear + 10. Suspension bracket and steering + 11. Brake system + 12. Body + 13. Electric equipment + 14. Electroschemes
|
ENGINE OF 2,0 L
Removal and installation
PERFORMANCE ORDER |
1. Disconnect the battery from weight. Merge cooling liquid and disconnect a radiator hose from the thermostat case. |
2. Remove the carburetor, having marked all disconnected hoses and wires. |
3. Disconnect from a collector all vacuum hoses. |
4. Unscrew nuts, having greased them with getting liquid. Displace a collector in easy blows and remove. |
5. Clear the demountable planes of a collector and a head of cylinders. Check deformation of the planes, if necessary прошлифуйте the head plane (having removed it) and replace a collector. |
6. Installation is carried out upside-down. Replace laying. Nuts of a collector tighten with the moment of 22 N of m. |
|
ENGINE OF 2,4 L
Inlet collector of the engine of 2,4 l
1. Air offtake 2. Ventilation hose 3. Inlet branch pipe 4. Pipe 5. Cables of management of a zaslonka and kick-down-mode 6. Throttle branch pipe 7. Laying
|
8. Hose of ventilation of a case 9. Hose of the amplifier of brakes 10. Vacuum hose 11. Wire 12. Coil 13. Leveling chamber 14. Collector |
Removal and installation
PERFORMANCE ORDER |
1. Execute a decompression. For this purpose disconnect the socket in a back part of a fuel tank, start the engine and after its stop switch off ignition. |
2. Disconnect the battery from weight. Merge cooling liquid and disconnect a radiator hose from the thermostat case. |
3. Designate and disconnect from a collector all hoses and wires. Carefully disconnect and muffle gasoline pipe lines. |
4. Disconnect from the ignition distributor a coil wire. |
5. Remove the leveling chamber. |
6. Remove the fuel distributor with nozzles. |
7. Remove the ignition distributor. |
8. Unscrew nuts and bolts and remove a collector. |
9. Clear the demountable planes of a collector and a head of cylinders. |
10. Installation is carried out upside-down. Replace laying of a collector and the leveling chamber. Nuts of a collector tighten with the moment of 16 N of m, since a nut in an average part of a collector. Execute necessary adjustments. |
|
ENGINE OF 2,6 L
Inlet collector of the engine of 2,6 l
1. Filter 2. Carburetor 3. Laying 4. Top hose of a radiator 5. Perepuskna liquid hose 6. Connecting hose 7. Heater hose 8. Hose of the amplifier of brakes
|
9. Vacuum hose 10. Wire of the sensor of temperature of the conditioner 11. Wire of the sensor of temperature 12. Wire of the index of temperature 13. Collector 14. Laying |
Removal and installation
PERFORMANCE ORDER |
1. Disconnect the battery from weight. Remove the air filter. |
2. Merge cooling liquid and disconnect a radiator hose from the thermostat case. |
3. Remove the carburetor. |
4. Remove a final branch pipe, the thermostat and laying. |
5. Remove the secondary air filter and a branch pipe. |
6. Remove a masloukazatel. |
7. Remove the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix. Remove a compressor arm. |
8. Designate and disconnect from a collector and the thermostat all hoses and wires. Carefully disconnect and muffle gasoline pipe lines. Take aside conducting and the hoses disturbing to removal of a collector. |
9. Remove the retsirkulyatsiya valve. |
10. Unscrew nuts and remove a collector. |
11. Clear the demountable planes of a collector and a head of cylinders. Check deformation of the planes, if necessary прошлифуйте the head plane (having removed it) and replace a collector. On a new collector establish all sensors and valves. |
12. Installation is carried out upside-down. Replace all laying and a sealant. Collector nuts at first tighten by hand, and then with the moment of 22 N of m, since a nut in an average part of a collector. Tighten bolts of an arm of the compressor with the moment of 45 N of m, the compressor – 24 N of m, the thermostat – 12 N of m. Check operation of all sensors and control lamps on the dashboard. |
|
ENGINES 3,0 AND 3,5 L
Leveling chamber of the engine of 3,0 l
1. Air offtake 2. Bolts of adjustment of a cable of an accelerator 3. Zaslonka cable 4. Accelerator cable 5, 8. Vacuum hose 6. Hose of the amplifier of brakes 7. Socket of the sensor of temperature of the valve of a retsirkulyatsiya 9. Bolts of a tube of a retsirkulyatsiya
|
10, 16, 20, 22. Laying 11. Coil wire 12. Coil 13. Arm of a jellied mouth 14. Ventilation hose 15. throttle branch pipe 17, 18. Bolts and nuts 19. Leveling chamber 21. Retsirkulyatsiya valve 23, 24. Racks |
Inlet collector of the engine of 3,0 l – otsoyedinyaeiy details at removal
N–details subject to replacement at assembly 1. Gasoline pipe line of a high pressure 2. Return gasoline pipe line 3. Vacuum hose 4. I will corrode control runs the engine 5. Branch pipe, distributor and pressure regulator 6. Vacuum distributing 7. Socket of the sensor of the index of temperature of liquid 8. The socket of the sensor of temperature of liquid for the conditioner 9. Socket of the sensor of temperature of liquid of a control system of the engine 10. Thermoswitch socket
|
11. Top hose of a radiator 12. Perepuskna hose 13. Bolts of fastening of a pipe of a heater 14, 16, 18. Laying 15. Collector 17. Final branch pipe 19. Thermostat 20. Conditioner thermoswitch 21. Sensor of temperature of liquid of a control system 22. Thermoswitch 23. Sensor of the index of temperature of liquid 24. Thermovalve |
Leveling chamber of the engine of 3,5 l
1. Cover 2. Switching block 3. Vacuum tube And 4. Vacuum hose And 5. Receiver 6. Solenoid of the valve of absorption 7. Arm 8. A vacuum tube In 9. A vacuum hose In
|
10. Arm 11, 12, 13. Arms of the leveling chamber 14–18. Details of system of a retsirkulyatsiya (valve, sensor, tube and laying) 19. Throttle branch pipe 20. Laying 22. Leveling chamber 23. Top section 24, 25, 26. Laying |
Inlet collector of the engine of 3,5 l
N–details subject to replacement at assembly 1. Wires of nozzles 2. The fuel distributor with nozzles 3, 6. Insulator 4. Pressure regulator 5, 9,12. Ring 7. Bracket 8. Nozzles 10. Sealant 11. Gasoline pipe line
|
14. Fuel distributor 15. Collector 16. Sensor of the index of temperature of liquid 17. Sensor of temperature of liquid of a control system 18, 19. Hoses 20–22. Final branch pipes 23. Inlet branch pipe 24. Thermostat 25. Case 26. Laying |
Removal and installation
PERFORMANCE ORDER |
1. Execute a decompression. For this purpose disconnect the socket in a back part of a fuel tank, start the engine and after its stop switch off ignition. |
2. Disconnect the battery from weight. Merge cooling liquid. |
3. Disconnect an air line. |
4. Unscrew bolts of adjustment of an accelerator. |
5. Designate and disconnect from a collector all available hoses and wires. |
6. Disconnect from the ignition distributor a coil wire. |
7. Remove the coil. |
8. Remove a throttle branch pipe and take aside (hoses of system of cooling from a branch pipe not to disconnect). Remember an arrangement of bolts of fastening of a branch pipe. Remove laying. |
9. Unscrew the top bolts of racks, bolts of fastening of the leveling chamber and remove the chamber and laying. |
10. Remove racks. |
11. Disconnect both gasoline pipe lines and vacuum hoses, remove the fuel distributor. Disconnect other hoses to which access (a hose of a radiator, perepuskny a hose and vacuum distributing became possible). |
12. Unscrew bolts and remove the collector chamber with laying. |
13. Clear the demountable planes of chambers of a collector and a head of cylinders. Check deformation of the planes if the deviation from the plane exceeds 0,3 mm, a collector replace and rearrange on a new collector all sensors and valves. |
14. Installation is carried out upside-down. Replace all laying (hermetic not to grease) and a sealant. Tighten all connections by the demanded moments. |
|
|
|