Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.21. Maslookhladitel

GENERAL INFORMATION

Maslookhladitel of 4-cylinder engines

1. Bolt of the cap union
2. Laying
3. Tubes of the final party
4. Tubes of the pressure head party
5. Hoses
6. Maslookhladitel
7. Arm

Maslookhladitel of 6-cylinder engines

1, 9. Bolt of the cap union
2, 10. Laying
3. Maslookhladitel
4. Rack
5. Arm
6. Union
7. Pressure head tube
8. Exhaust pipe
11, 12. Hoses

Arrangement of bolts of fastening of tubes and maslookhladitel of 4-cylinder engines

Fastening bolts – are specified by shooters

The correct arrangement of pressure head and final tubes at assembly

1, 5. Hoses

2. Clamping collar

3. Limiter

4. Bolt of the cap union

Removal and installation

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Merge oil.
3. Remove forward facing.
4. Unscrew bolts of unions, holding a key the welded nut on the cooler case. Get laying.
5. Unscrew bolts and remove a maslookhladitel.
6. Disconnect from a maslookhladitel hoses and tubes.
7. Check a condition of edges of a cooler and tubes. If necessary replace or repair.
8. At installation execute the following. On 4-cylinder engines: a long hose (the release party) establish above, and short – from below. On 6-cylinder engines: at first tighten a bolt of the union of a final hose, and then inlet then tighten a bolt of a clamping collar.
9. Further installation is carried out upside-down. Warm up the engine and check oil level.