Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      - 3.4.11. Removal and engine installation
         3.4.11.1. Engine of 2,6 l
         3.4.11.2. 12-klapanny engine of 3,0 l
         3.4.11.3. 24-klapanny engine of 3,0 l
         3.4.11.4. Engine of 3,5 l
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      + 3.4.24. Head of cylinders
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






3.4.11.1. Engine of 2,6 l

GENERAL INFORMATION

ORDER OF REMOVAL OF THE ENGINE OF 2,6 L

Disconnected hoses and wires at dismantle of the 4-cylinder engine

1. Butterfly valve cable
2. Heater hose
3. Hose of the amplifier of brakes
4. Perepuskna hose of system of cooling
5. Hose of system of cooling
6. Radiator hose
7. Burn down control systems of the engine
8. The socket of the sensor of temperature of liquid for the conditioner
9. The socket of the sensor of the index of temperature of liquid for the conditioner
10. Vacuum hose
11. Socket of the sensor of temperature of liquid of a control system of the engine

13. Socket of the sensor of oxygen
14. Socket of the sensor of pressure of oil
15. Belt of the pump of the hydraulic booster
16. Pump of the hydraulic booster
17. Belt of the compressor of the conditioner
18. Conditioner compressor
19. Gasoline pipe line
20. Generator socket
21. A wire on weight
22. Forward exhaust pipe
23. Bracket of fastening of a gasoline pipe line
24. Guard
25. bolt of a forward support
26. Engine

Removal

PERFORMANCE ORDER
1. Depressurize the conditioner (if it is provided) in car-care center.
2. Remove a cowl.
3. Lift the car and remove engine guards.
4. Merge liquid from cooling system.
5. Merge oil from transmission, the engine, a transfer case and a forward reducer.
6. Remove the air filter.
7. Remove both casings of the fan.
8. Remove a radiator.
9. Disconnect a butterfly valve cable.
10. Disconnect on the engine hoses of a heater, system of cooling and the amplifier of brakes.
11. Disconnect the big multicontact socket of conducting of a control system of the engine.
12. Disconnect a vacuum hose and turn out the sensor of the index of temperature of liquid.
13. Disconnect wires from the sensor of oxygen and from the sensor of pressure of oil.
14. Remove a belt of the pump of the hydraulic booster, having released bolts of fastening of the pump.
15. Remove the pump of the hydraulic booster and take aside, without disconnecting from the highway.
16. Remove a belt and the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix.
17. Disconnect fuel hoses, previously having executed a decompression (on injector engines).
18. Disconnect 3 sockets on the generator.
19. Disconnect a mass wire from the block of cylinders.
20. Disconnect from a collector an exhaust pipe and fix a pipe a wire.
21. Disconnect all hoses of a tank with an absorber which conduct to a partition of a motor compartment.
22. Remove a bracket of fastening of gasoline pipe lines on the engine.
23. Attach таль the lift and will hang out the engine.
24. Remove from the right support a guard.
25. Unscrew bolts of fastening of support of the engine to a frame.
26. Carefully lift the engine and get from a motor compartment. Establish the engine on supports (not on the pallet).

Installation

PERFORMANCE ORDER
Installation of the engine is carried out upside-down. First of all establish the engine, wrap bolts of support and tighten them with the moment of 35 N of m. Replace laying of an exhaust pipe on a collector and fastening bolts. Bolts of fastening of a radiator tighten with the moment of 7 N of m. Fill in liquid, oil and start the engine. After warming up restore levels of liquids. Fill the conditioner in car-care center. Adjust a cable, belts, idling and ignition.