Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. Mechanism of management of transmission
      9.3.5. Epiploon of a shaft of a case of transmission
      9.3.6. Removal and transmission installation
      9.3.7. Transfer case
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward driveshaft and crosspieces
      + 9.3.10. Back driveshaft and crosspieces
      9.3.11. Forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semi-axes and epiploons of a forward axis
      9.3.15. Reducer of a forward axis
      9.3.16. Dismantling of CV JOINTS
   + 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.3.6. Removal and transmission installation

GENERAL INFORMATION

Automatic transmission КМ148 (1987-89)

1. Handle
2. Panel
3. Шплинт
4. Axis
5. Butterfly valve cable
6. Socket of the solenoidal
valve of inclusion of the highest
broadcasts (overdrive-valve)
7. Speedometer cable
8. A branch pipe for filling and check of level of liquid
9. Ring
10. Back driveshaft
11. Forward driveshaft
12. Shaft of cross-section draft
13. Draft

Automatic transmission КМ148 (1987-89), continuation

14. Bolt of fastening of an exhaust pipe
15. Tubes of a cooler of transmission liquid
16. Cover of access to the hydrotransformer
17. Special bolts
18. Socket of the sensor of a control lamp of inclusion of a forward leading axis
19. Arm of an exhaust pipe
20. Cross-piece
21. Arm of a transfer case
22. Plug
23. Transmission assembled with a transfer case

Automatic transmission of V4AW2 (1990-98)

1. A branch pipe for filling and check of level of liquid
2. Ring
3. Tip of a cable of a butterfly valve
4. Dustproof cover
5. Cable of management of transmission
6. Speedometer cable
8. Socket of the switch of the provisions HIGH/LOW
9. The socket of the sensor of a control lamp of inclusion of a drive on all wheels
10. The socket of the sensor of work of interaxal differential in a blocking mode
11. Socket of the sensor of blocking of interaxal differential
12. Socket of the sensor of inclusion of a forward axis
13. The socket of the blocking switch
15. Cooler tube
A.Smazat DIAMOND ATF SP liquid or equivalent
N–is subject to replacement

Automatic transmission of V4AW2 (1990-98), continuation

16. Starter
17, 18. Guard
19, 20. Arms
21. An access cover to
to the hydrotransformer
22. Torsion of a transmission support
23. Arm of a transfer case
24. Cross-piece
25. Buffer of a support of the engine
26. Arm of a guard of a transfer case
27. Buffer
28. Hydrotransformer bolt
29. Transmission assembled with a transfer case
31. Laying
A.Oboznacheniye of a bolt
B.Moment of an inhaling
V.Razmery of a bolt of L and D

Automatic transmission of V4AW3 (1994-98)

1. A branch pipe for filling and check
liquid level
2. Ring
3. Tip of a cable of the throttle
zaslonka
4. Dustproof cover
5. Cable of management of transmission
7. Socket of the sensor of speed
8. Socket of the switch of provisions
HIGH/LOW of a transfer case
9. The socket of the sensor of a control lamp of inclusion of a drive on all wheels
10. The socket of the sensor of work of interaxal differential in a blocking mode
11. Socket of the sensor detector of blocking of interaxal differential
12. Socket of the sensor detector of inclusion of a forward axis
13. The socket of the blocking switch
14. Socket of the solenoidal valve
15. Cooler tube
A.Smazat DIAMOND ATF SP liquid or equivalent
N–is subject to replacement

Automatic transmission of V4AW3 (1994-98), continuation


16. Starter
17, 18. Starter guard
24. Cross-piece
26. Arm of a back support
engine
27. Buffer
28. Fastening bolt
hydrotransformer
29. Transmission assembled with a transfer case
30. Case of the mechanism of management of transmission
31. Laying
A.Oboznacheniye of a bolt
B.Moment of an inhaling
V.Razmery of a bolt of L and D

CARS OF 1983-89.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove a forward exhaust pipe, having disconnected from a collector and converter.
3. Disconnect kick-down-draft.
4. Remove a cover of the selector and the selector panel, remove the selector.
5. Lift the car, remove a guard of a transfer case.
6. Remove the mechanism of change of transfers of transmission and management of a transfer case.
7. Merge from transmission liquid.
8. Disconnect cooler tubes, muffle and fix in vertical situation.
9. Disconnect driveshafts.
10. Disconnect from transmission of a wire and cables.
11. Unscrew bolts of fastening of the hydrotransformer for what uncover and turn the crankshaft, turning on bolts consistently.
12. Remove a starter, take aside and fix (it is recommended to disconnect at first wires).
13. Remove from a cross-piece a back support of transmission.
14. Remove a cross-piece, considering considerable weight and the sizes of this detail.
15. Remove a support of a transfer case, unscrew bolts of fastening of a bell-shaped case and remove transmission, having displaced it back, having lowered and having removed from directing pins.
16. Installation is carried out upside-down.
17. Replace all laying and a sealant, tighten connections with the moments specified an illustrations.
18. Bolts of fastening of the hydrotransformer to a flywheel tighten with the moment of 35-42 N of m.
19. Adjust drafts and cables.

CARS OF 1990-98.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the mechanism of management of a transfer case.
3. Lift the car, remove a guard of a transfer case.
4. Remove a forward exhaust pipe, having disconnected from a collector and converter.
5. Merge liquid from transmission and oil from a transfer case.
6. Disconnect driveshafts, having designated their situation.
7. A forward shaft submit forward, incline and get from a reducer.
8. Remove a refueling branch pipe.
9. Disconnect from draft transmission, remove from a case shaft a cover.
10. Designate and disconnect from transmission of a wire and cables, including a speedometer cable.
11. Disconnect from transmission of a tube of a cooler.
12. Remove a starter and a thermal guard (if it is provided).
13. Substitute a jack under the engine pallet.
14. Substitute under transmission the cart with a jack, but transmission yet do not hang out.
15. Slightly will hang out the engine and remove the right and left forward support.
16. Remove the bottom cover of a bell-shaped case.
17. Remove an arm of a transfer case, торсион, the buffer and a guard arm.
18. Slightly will hang out transmission.
19. Unscrew 2 bolts of a cross-piece, lift a jack on 6 mm and remove a cross-piece.
20. Remove transmission. At removal execute the following.
21. Uncover
22. Unscrew 6 bolts of fastening of the hydrotransformer, having asked the assistant to turn the crankshaft.
23. Carefully lower a back part of transmission assembled with a transfer case and remove from the engine.
24. Incline a forward part of transmission and carefully lower, watching to touching a back extreme cross-piece, and get from under the car.
25. Installation is carried out upside-down.
26. Replace all laying and a sealant, tighten connections with the moments specified an illustrations
27. Bolts of fastening of the hydrotransformer to a flywheel tighten with the moment of 34-41 N of m, bolts of fastening of transmission – with the moment of 75 N of m, cross-piece bolts – 6 N of m.
28. Adjust drives of management of transmission.