Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. Mechanism of management of transmission
      9.3.5. Epiploon of a shaft of a case of transmission
      9.3.6. Removal and transmission installation
      9.3.7. Transfer case
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward driveshaft and crosspieces
      + 9.3.10. Back driveshaft and crosspieces
      9.3.11. Forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semi-axes and epiploons of a forward axis
      9.3.15. Reducer of a forward axis
      9.3.16. Dismantling of CV JOINTS
   + 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.3.4. Mechanism of management of transmission

GENERAL INFORMATION

Mechanism of management of transmission МА904А

1. Handle
2. Button
3. Screw
4. Clown
5. Rod
6. Selector
7. Sector
8, 10. Cover of an ukazvatel of position of the selector
9. The blocking switch
11. Arm cover
12. Lever
13. Draft

Order of removal of details of the mechanism of management of transmission of KM 148

1. Plate
2. Floor section
3. Switch socket
the highest transfer
4. Handle
5. Wires and switch socket
the highest transfer
6. Cover
7. The blocking switch
and forward socket
8. A wire of a control lamp of the index of position of the selector also I will corrode
9. Index panel
10. Arm
11. Guard
12. Шплинт
13. Draft In
14, 18, 24. Cover
15. Lock ring
16. Spring
15, 25. Plug
19. Shaft of cross-section draft
20. Draft And
21. Cap
22. Plug
23. Arm of cross-section draft
26. Axis

Designated N of a detail are subject to replacement.

Order of removal of details of the mechanism of management of V4AW2 (3) transmission

1. Fastening of a cable of blocking
(from the selector)
2. Fastening of a cable of fixing of transfers
(from the selector)
3. Fastening of a cable of management by transmission (from the selector)
4. Selector
5. Guard of a transfer case
6. Fastening of a cable of management by transmission (from transmission)
7. Top lever
8. Cable
9. Cable arm
10. Cable and arm

Designated N of a detail are subject to replacement.

Removal and installation


Prevention

The part of works is carried out under the car.


CARS OF 1983-86.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove the selector handle.
3. Remove the central section and the index of position of the selector.
4. Disconnect the socket of a control lamp and the switch.
5. Disconnect draft from the lever, having unscrewed a nut, working under the car.
6. Unscrew screws and remove an arm.
7. Assembly is carried out upside-down taking into account the following.
8. Grease rubbing parts of the lever and draft with SAE J310А or NLGI N3 greasing.
9. Adjust position of the blocking switch (see subsection 9.3.2.1).
10. If draft acted in film from the lever, establish the selector in neutral situation, then move draft, having established transmission in neutral situation (block wheels).
11. Be convinced that the starter joins only in positions P and N and in operation of a signal of a backing in situation R.
12. Adjust the clown of the selector. For this purpose rotating the clown. establish distance between end faces of the selector and the clown of 11,3-12,7 mm.

CARS OF 1987-89.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Displace a cover down and disconnect the socket of the switch of the highest transfer (оverdrive) on the handle.
3. Unscrew screws and remove the handle, disconnect the top socket of the switch, remove a cover.
4. Remove the index of position of the selector, having unscrewed screws of a cover and having disconnected sockets of the blocking switch and a control lamp.
5. Remove an arm with the management mechanism.
6. For this purpose, working from below, unscrew nuts, disconnect draft In from the lever, cross-section draft from draft In, remove washers and a guard.
7. Remove a cover, remove a lock ring, springs, plugs and a sealant of cross-section draft.
8. Unscrew bolts of arms on a transfer case, расшплинтуйте and disconnect cross-section draft from drafts And and In, remove plugs and washers.
9. Remove a shaft of cross-section draft.
10. Rasshplintuyte also disconnect draft And, remove plugs and a washer.
11. Replace шплинты connections of drafts (1 – draft And, 2 – a shaft of cross-section draft).
12. Assembly is carried out upside-down taking into account the following.
13. Grease the specified places with SAE J310А or NLGI N3 greasing.
14. Replace all specified details.
15. Draft In establish having transferred the selector and transmission to neutral situation.
16. Be convinced of correctness of installation of plugs and draft washers In (1 – the lever, 2 – draft In).
17. Tighten all connections according to the demanded moments.
18. Check operation of the mechanism of management as transmission and inclusion of the highest transfer by button pressing on the handle.

CARS OF 1990-98.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Disconnect from the selector all cables.
3. Unscrew bolts and remove the selector assembled.
4. Unscrew bolts and remove a guard of a transfer case.
5. Unscrew a nut of fastening of the top lever to an arm on transmission.
6. Rasshplintuyte also disconnect a cable from the lever.
7. Unscrew nuts and bolts of fastening of arms (6–8 pieces) and remove arms of a cable and a cable tip.
8. Remove a cable.
9. Assembly is carried out upside-down taking into account the following.
10. Grease rubbing places (axis).
11. Tighten all connections with the moments specified illustrations.
12. Adjust cables in the following order.
Cable of management of transmission
13. Move the selector to situation N, working under the car release a lock-nut, slightly submit a cable (2) towards a forward part of transmission and tighten a nut (1).
Fixing cable
14. Move the selector to situation P and adjust the provision of a cable so that the red label (the cable termination) was in the specified situation, tighten a nut (1, 3 – a cable, 2 – a clamp emphasis, 4 – a nut, 5 – a clamp cam, 6 – location of the termination of a cable).
Blocking cable
15. Dress a spring (the selector is in situation P) and a washer definitely (1 – a cable, 2 – an axis, 3 – a clamp cam, 4 – a washer, 5 – a spring).
16. Slightly submit a cam in the arrow direction against the stop and tighten a nut.