Mitsubisi Padzhero + 1.1. Dashboard and control units + 2. Maintenance + 3. Engines + 4. Cooling system + 5. Greasing system + 6. Power supply system + 7. Release system + 8. Fuel system - 9. Running gear + 9.1. Mechanical transmission + 9.2. Coupling - 9.3. Automatic transmission 9.3.1. Adjustments + 9.3.2. The blocking switch 9.3.3. Check of adjustment of a cable of management by transmission 9.3.4. Mechanism of management of transmission 9.3.5. Epiploon of a shaft of a case of transmission 9.3.6. Removal and transmission installation 9.3.7. Transfer case 9.3.8. Forward and back epiploons + 9.3.9. Forward driveshaft and crosspieces + 9.3.10. Back driveshaft and crosspieces 9.3.11. Forward leading axis 9.3.12. A nave with a manual unblocking 9.3.13. A nave with an automatic unblocking 9.3.14. Forward semi-axes and epiploons of a forward axis 9.3.15. Reducer of a forward axis 9.3.16. Dismantling of CV JOINTS + 9.4. Zadny Bridge + 10. Suspension bracket and steering + 11. Brake system + 12. Body + 13. Electric equipment + 14. Electroschemes
|
CARS OF 1983-86.
Adjustment of inclusion of a kick-down-mode
Screw of adjustment of inclusion of a kick-down-mode (М904А)
|
The adjusting screw is on the left side of a transmission case.
1. To a cooler
2. Adjusting screw |
PERFORMANCE ORDER |
1. Unscrew a lock-nut on 5 turns. |
2. Be convinced that the screw rotates without jammings. |
3. Tighten the screw with the moment of 7,8 N of m. |
4. Unscrew the screw on 3,5 turns, and, holding it, tighten a lock-nut with the moment of 40-55 N of m. |
|
Adjustment of a tape of inclusion of a backing and the lowest transfer (low-reverse)
Screw of adjustment of inclusion of a backing and the lowest transfer
PERFORMANCE ORDER |
1. Lift the car. |
2. Unscrew a lock-nut on 5 turns. |
3. Be convinced that the screw rotates without jammings. |
4. A key of MD998358 tighten the screw with the moment of 4,9 N of m. |
5. Unscrew the screw on 7 turns, and, holding it, tighten a lock-nut with the moment of 34-47 N of m. |
6. Establish the pallet and tighten bolts with the moment of 15-20 N of m. |
7. Fill in liquid. |
|
Kick-down-drive adjustment
CARS OF 1983-86.
Adjustment of system of drafts of a kick-down-mode (М904А)
|
1. Draft With
2. Bolt
3. Draft In
4. Control lever butterfly valve
5. Draft And |
Check of turn of draft of management by a butterfly valve (after adjustment of other drafts)
|
1. Situation at completely open butterfly valve
2. Situation idling
3. Lever |
PERFORMANCE ORDER |
1. Release bolts so that drafts In and With freely moved. |
2. Warm up the engine to 80 ° With and be convinced that fast idling is completely disconnected (a cam of the lever of an air zaslonka of the carburetor should not adjoin to a cam of the lever of a butterfly valve). |
3. Submit draft And (or a control lever a butterfly valve) to the limiter of idling and establish drafts in the situation corresponding to idling. |
4. Tighten a bolt connecting drafts In and Page. |
5. Be convinced that when opening butterfly valve the lever on transmission turns on 47,5–54 °, and also that at slow return of draft of a butterfly valve from completely open provision of a zaslonka the lever on transmissions comes back to the situation corresponding to idling under the influence of a spring. |
|
CARS OF 1987-89.
Adjustment of a kick-down-drive (КМ148)
|
1. Completely open zaslonka
2. Idling
3. Arm |
PERFORMANCE ORDER |
1. Believe idling turns (after adjustment of idling adjust a butterfly valve cable). |
2. Check distance between the limiter of a cable and a cap which 52–53 mm should be at completely open zaslonka. |
3. If necessary establish distance moving of an arm of a cable at the released bolts. |
|
CARS OF 1990-98.
Adjustment of a gap of a cable of a kick-down-drive (and/m with engines of 3,5 l and 3,0 l 1990-94gg.)
|
1. Nuts
2. Cover
3. Cable limiter |
Adjustment of a gap of a cable of a kick-down-drive (and/m with the engine of 3,0 l of 1995)
|
1. Nuts
2. Cable limiter
3. Cover |
PERFORMANCE ORDER |
Engine of 3,5 l and 3,0 l (1990-94) |
1. Press a pedal of a butterfly valve and check distance between the limiter of a cable and a dustproof cover which should be 0–1 mm. |
2. If necessary establish distance rotation of adjusting nuts of a cover of a cable. |
Engine of 3,0 l (1995) |
3. Remove a cover of a cable and and check distance between the limiter of a cable and a cover which 34–35 mm should be at completely open zaslonka. |
4. If necessary establish distance rotation of adjusting nuts of a cover of a cable. |
|
|
|