Mitsubisi Padzhero + 1.1. Dashboard and control units + 2. Maintenance - 3. Engines 3.1. Candles 3.2. Check of wires + 3.3. Ignition system - 3.4. Major maintenance of the engine 3.4.1. Engine electric equipment 3.4.2. Ignition distributor + 3.4.3. Generator 3.4.4. Battery 3.4.5. Starter 3.4.6. Traction relay of a starter 3.4.7. Sensors + 3.4.8. Instructions on service and engine repair 3.4.9. Compression check in cylinders of engines 3.4.10. Specifications of engines + 3.4.11. Removal and engine installation 3.4.12. Cover of a head of the block of cylinders + 3.4.13. Rollers and yokes 3.4.14. Thermostat of system of cooling 3.4.15. Inlet collector 3.4.16. Final collector 3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging) 3.4.18. Turbokompressor 3.4.19. Turbonagnetatel 3.4.20. Radiator 3.4.21. Maslookhladitel 3.4.22. Fan 3.4.23. The pump of cooling liquid + 3.4.24. Head of cylinders 3.4.25. Valves and springs 3.4.26. Saddles 3.4.27. Replacement of directing plugs 3.4.28. Hydropushers - 3.4.29. Gear belt and covers 3.4.29.1. Engine of 2,0 l 3.4.29.2. Engines of 2,4 l 3.4.29.3. Engines of 3,0 l and 3,5 l 3.4.30. Chain and cover (engine of 2,6 l) 3.4.31. Oil pallet 3.4.32. Oil pump and saylent-rollers (vibrogasitel) 3.4.33. Cam-shafts and support 3.4.34. Check of a condition of a cam-shaft + 3.4.35. Pistons and rods 3.4.36. Back epiploon 3.4.37. Radical bearings 3.4.38. Flywheel + 3.4.39. Exhaust system + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l + 4. Cooling system + 5. Greasing system + 6. Power supply system + 7. Release system + 8. Fuel system + 9. Running gear + 10. Suspension bracket and steering + 11. Brake system + 12. Body + 13. Electric equipment + 14. Electroschemes
|
Gear belt and adjacent details of the engine of 3,5 l
1. Fan 2. Pulley 3. Compressor
|
4, 7. Arms 5. Cover 6. Pump of the hydraulic booster |
The details shown at removal of a belt (3,5 l)
1, 4. Cover 2. Socket of the sensor of rotation of the crankshaft 3. Pulley 5. Belt
|
6. Device of an automatic tension 7. Roller of a natyazhitel 8. Lever
|
Removal
PERFORMANCE ORDER |
1. Disconnect the battery from weight. |
2. Merge liquid. |
3. Disconnect a hose of a radiator and remove the top casing of the fan. |
4. Remove the fan with the coupling. |
5. Remove all belts of hinged units.
|
6. Remove a fan pulley from the cooling pump.
|
7. Remove the pump of the hydraulic booster and an arm. Take the pump aside, without disconnecting from the highway. |
8. Remove an arm of a roller of a natyazhitel.
|
9. Remove the conditioner compressor. Take the unit aside, without disconnecting from the highway, and fix. Remove a compressor arm.
|
10. Remove a fan arm.
|
11. Remove the top covers of a belt and laying. On the engine of 3,5 l remove the sensor of rotation of the crankshaft. |
12. Remove the bottom cover of a belt. |
13. Establish the piston of the 1st cylinder in VMT of a step of compression. From this point rotation of the crankshaft is not allowed. |
14. Unscrew a pulley bolt, holding the crankshaft a special key and remove a pulley. |
15. Release bolts of a natyazhitel and carefully remove a gear belt, having designated the rotation direction. |
|
Belt installation on the engine of 3,0 l
PERFORMANCE ORDER |
1. Check a belt condition, at detection of any defects replace. |
2. Check a condition of a roller of a natyazhitel and teeths of asterisks. |
3. Establish a natyazhitel, turn counter-clockwise and fix bolts. |
4. Check combination of labels on asterisks and dress a belt, being guided on the put arrow. The belt should be tense between asterisks of the crankshaft and the left cam-shaft. When clothing slightly press on an asterisk of the left cam-shaft counter-clockwise. If a belt will pull, labels should coincide. |
5. Establish a flange on a crankshaft asterisk. |
6. Release a bolt of a natyazhitel that the roller rested against a belt. |
7. Smoothly, without breakthroughs, turn the crankshaft on 2 turns clockwise and check combination of labels.
|
8. Tighten a bolt of a natyazhitel with the moment of 25 N of m.
|
9. Establish all details upside-down. Replace the damaged laying of covers, having laid them in a cover on glue 3M EC 870. Tighten bolts of covers with the moment of 11 N of m.
|
|
Belt installation on the engine of 3,5 l
PERFORMANCE ORDER |
1. Check a belt condition, at detection of any defects replace. |
2. Check a condition of a roller of a natyazhitel and teeths of asterisks. |
|
3. Compress a natyazhitel in a vice and fix, having inserted into openings a wire in diameter of 1,4 mm. Establish a natyazhitel and tighten a bolt with the moment of 24 N of m.
|
4. Establish a pulley of the crankshaft and turn a crankshaft asterisk so that it was displaced on 3 teeth clockwise. |
5. Combine labels of asterisks of cam-shafts of the left head. |
6. Combine labels of asterisks of cam-shafts of the right head, fix a key from a provorachivaniye. |
|
7. Be convinced of combination of labels of a cam-shaft of the right head of cylinders and fix a belt 2 brackets. |
8. Get a belt on a pulley of the pump of cooling. |
9. Be convinced of combination of labels of a cam-shaft of the left head of cylinders and fix a belt 2 brackets. |
10. Get a belt on an intermediate roller. |
11. Having combined labels on a crankshaft asterisk, turn the crankshaft on 1 tooth counter-clockwise. |
12. Dress a belt on an asterisk of the crankshaft and on a roller of a natyazhitel. |
13. Place a roller of a natyazhitel so that the opening under a pin was turned up. Press a roller and tighten a bolt. |
14. Combine labels on a crankshaft asterisk. |
15. Check combination of all labels. |
16. Turn the crankshaft on 1/4 turn counter-clockwise, then turn clockwise and combine labels. |
|
17. Release a bolt of a natyazhitel (2). A special key turn a natyazhitel with the moment of 9,4 N of m, having pulled a belt, and at the same time tighten the central bolt of a natyazhitel with the set moment. At a tightening of a bolt of a natyazhitel the roller should not rotate (1. An opening under a pin; 3. Roller of a natyazhitel). |
18. Get from a natyazhitel a wire and be convinced that it is possible to get a pin easily. |
|
19. Turn the crankshaft on 2 turns and leave in this situation for 5 minutes. Check freedom of moving of a pin in an opening of a natyazhitel. If the pin comes with small effort, check a vystupaniye of a rod of a natyazhitel (And) which 3,8–4,5 mm should be. Otherwise repeat procedure of clothing and adjustment of a tension of a belt. |
20. Check combination of all labels on asterisks. |
21. Establish all details upside-down. Replace the damaged laying of covers, having established them in a cover on glue 3M EC 870. Tighten bolts of covers with the moment of 11 N of m. After start-up of the engine hear to noise from a belt. If unusual noise are distributed, stop the engine and check installation and a belt tension. Upon termination of adjust belts of a drive of hinged units. |
|
|
|