Mitsubisi Padzhero + 1.1. Dashboard and control units + 2. Maintenance - 3. Engines 3.1. Candles 3.2. Check of wires + 3.3. Ignition system - 3.4. Major maintenance of the engine 3.4.1. Engine electric equipment 3.4.2. Ignition distributor + 3.4.3. Generator 3.4.4. Battery 3.4.5. Starter 3.4.6. Traction relay of a starter 3.4.7. Sensors + 3.4.8. Instructions on service and engine repair 3.4.9. Compression check in cylinders of engines 3.4.10. Specifications of engines + 3.4.11. Removal and engine installation 3.4.12. Cover of a head of the block of cylinders - 3.4.13. Rollers and yokes 3.4.13.1. Engine of 2,0 l 3.4.13.2. Engine of 2,6 l 3.4.13.3. Engines of 2,4 l and 3,0 l 3.4.13.4. Engine of 3,5 l 3.4.13.5. Diesel engine 3.4.14. Thermostat of system of cooling 3.4.15. Inlet collector 3.4.16. Final collector 3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging) 3.4.18. Turbokompressor 3.4.19. Turbonagnetatel 3.4.20. Radiator 3.4.21. Maslookhladitel 3.4.22. Fan 3.4.23. The pump of cooling liquid + 3.4.24. Head of cylinders 3.4.25. Valves and springs 3.4.26. Saddles 3.4.27. Replacement of directing plugs 3.4.28. Hydropushers + 3.4.29. Gear belt and covers 3.4.30. Chain and cover (engine of 2,6 l) 3.4.31. Oil pallet 3.4.32. Oil pump and saylent-rollers (vibrogasitel) 3.4.33. Cam-shafts and support 3.4.34. Check of a condition of a cam-shaft + 3.4.35. Pistons and rods 3.4.36. Back epiploon 3.4.37. Radical bearings 3.4.38. Flywheel + 3.4.39. Exhaust system + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l + 4. Cooling system + 5. Greasing system + 6. Power supply system + 7. Release system + 8. Fuel system + 9. Running gear + 10. Suspension bracket and steering + 11. Brake system + 12. Body + 13. Electric equipment + 14. Electroschemes
|
Cam-shaft covers (engines 3,0)
Shooters on covers of a cam-shaft should coincide with an arrow on a head of cylinders. 1, 3. Shooters on covers 2. Places of drawing of hermetic
|
4. Shooters on a head of cylinders 5. Roller A 6. Towards a belt 7. Roller B |
Removal
PERFORMANCE ORDER |
1. Uncover heads of cylinders. |
2. Dress on hydropushers special brackets of Mv998443-01. Release bolts of covers of necks of a cam-shaft, slightly pressing on yokes. |
3. Turn out bolts of covers in the direction from a forward cover to back, thus ask the assistant to hold a cam-shaft reliably. It is impossible to allow, that the belt tension sharply increased at a cam-shaft exit from support (otherwise it is necessary to reinstall a cam-shaft and a belt). |
4. After removal of the roller remove a back cover and establish on the place, having fixed bolts by hand. If necessary this cover can be removed, having established in exchange an average cover. |
|
Installation
PERFORMANCE ORDER |
1. Disassemble the mechanism, check a condition of persistent surfaces of yokes, freedom of rotation of a roller, wear of the interfaced details and purity of lubricant channels. Worn-out details replace. |
2. Collect rollers with covers, сориентировав so that dredging on rollers was turned up, and covers were located according to their numbers. Grease all details. At installation of rollers the assistant should hold a cam-shaft. |
3. Further assembly is carried out upside-down. Brackets remove after an inhaling of bolts of fastening. Tighten bolts with the moment of 20 N of m. |
|
|
|