Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
   3.1. Candles
   3.2. Check of wires
   + 3.3. Ignition system
   - 3.4. Major maintenance of the engine
      3.4.1. Engine electric equipment
      3.4.2. Ignition distributor
      + 3.4.3. Generator
      3.4.4. Battery
      3.4.5. Starter
      3.4.6. Traction relay of a starter
      3.4.7. Sensors
      + 3.4.8. Instructions on service and engine repair
      3.4.9. Compression check in cylinders of engines
      3.4.10. Specifications of engines
      + 3.4.11. Removal and engine installation
      3.4.12. Cover of a head of the block of cylinders
      + 3.4.13. Rollers and yokes
      3.4.14. Thermostat of system of cooling
      3.4.15. Inlet collector
      3.4.16. Final collector
      3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
      3.4.18. Turbokompressor
      3.4.19. Turbonagnetatel
      3.4.20. Radiator
      3.4.21. Maslookhladitel
      3.4.22. Fan
      3.4.23. The pump of cooling liquid
      - 3.4.24. Head of cylinders
         3.4.24.1. Removal and installation
         3.4.24.2. Cleaning and check
      3.4.25. Valves and springs
      3.4.26. Saddles
      3.4.27. Replacement of directing plugs
      3.4.28. Hydropushers
      + 3.4.29. Gear belt and covers
      3.4.30. Chain and cover (engine of 2,6 l)
      3.4.31. Oil pallet
      3.4.32. Oil pump and saylent-rollers (vibrogasitel)
      3.4.33. Cam-shafts and support
      3.4.34. Check of a condition of a cam-shaft
      + 3.4.35. Pistons and rods
      3.4.36. Back epiploon
      3.4.37. Radical bearings
      3.4.38. Flywheel
      + 3.4.39. Exhaust system
   + 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes




3.4.24.2. Cleaning and check

GENERAL INFORMATION

Cleaning of a head consists at a distance the consolidation and deposit remains from chambers of combustion and heads of valves. When cleaning use a scraper from a firm tree or from plastic (drawing of scratches is not allowed). At the same time clear the demountable plane of the block of cylinders, having carefully closed cylinders rags.

After cleaning and washing of a head check a condition of the demountable planes. A plane tolerance with the block of cylinders from calibre – 0,05 mm in any place.

If the deviation does not exceed 0,20 mm, a head прошлифуйте. Otherwise a head replace.

If the deviation of the demountable plane of the block of cylinders from calibre exceeds 0,05 mm, прошлифуйте the block or replace. The manufacturer established norm of reduction of thickness of a head of cylinders when polishing – 0,20 mm.

On V6 engines follows also прошлифовать the plane of an inlet collector. After cleaning it is recommended to establish gazoraspredeleniye details.