Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
- 12. Body
   12.1. Maintenance and repair
   12.2. Vinyl furnish
   12.3. Upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repair of openings from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. Windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. Cover of a back compartment
   12.16. Bumpers
   12.17. Forward facing lattice
   12.18. External mirrors
   12.19. Forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. Hatch
   12.23. Holder of a spare wheel
   + 12.24. Salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. Ceiling upholstery
   12.28. Switch of the door lock
   + 12.29. Door glass, window regulator and window regulator electric motor
   12.30. Windscreen
   12.31. Back glass
   12.32. Vnutrisalonnoye rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. Electric equipment
+ 14. Electroschemes






12.20. Removal and installation covered

GENERAL INFORMATION

Forward wing (1983-91gg.) (on inserts – places of greasing by ES-870 glue (above), hermetic 8531 drawings on the top edge of a wing (section A-and), gluings of an edge of the protective panel to a wing (section in the V-in plane))

1. Lattice
2. Forward combination of lamps
3. Headlight facing
4. Bottom panel of a front
5. Gryazeotrazhatel
6. A condensed edge of the protective panel
7. Protective panel of a niche
8. Wing
9. Sealing pillow of a corner of a wing

Forward wing (1992-98) (on inserts – places of drawing of hermetic)

1. Gryazeotrazhatel
2. Forward index of turn
3. Protective panel

CARS OF 1983-91.

PERFORMANCE ORDER
1. Unscrew 6 screws and remove a forward lattice.
2. Remove a forward combination of lamps (see subsection 13.17.4) and facing of headlights.
3. Unscrew 4 screws and remove the bottom cross-section panel of a front.
4. Remove gryazeotrazhatel and the protective panel of a wheel niche.
5. Unscrew bolts and remove a wing, having tracked safety of a sealing pillow for protection of a forward corner of a wing.
6. Installation is carried out upside-down.
7. A sealing pillow establish on glue 3M Adhesive ES-870. An edge of the protective panel paste structure 3M ATD 8625.

CARS OF 1992-98.

PERFORMANCE ORDER
1. Remove a bell of facing of an aperture of a wheel niche (if it is provided) for what execute the following.
2. Paste masking tape on all length of lateral facing.
3. Cut off facing on a glutinous layer by means of a scaffold in thickness of 0,8 mm.
4. Drill rivets of facing a drill in diameter of 4-5,5 mm. Cores of rivets beat out (1 – an insert of a mortgage rivet, 2 – заклека, 3 – a drill, 4 – the facing panel).
5. Remove latches, having submitted facing on itself.

Prevention

If facing is established again, by means of a scaffold cut off a glutinous layer on a body not to break edge of the panel of facing. If glue does not give in to cutting, heat up it to 40 ° Page.


6. With Shpatel remove a sticky tape.
7. Remove masking tape.
8. Wipe a surface fat-free structure 3M ATD 8906.
9. Remove a forward combination of lamps (see subsection 13.17.4).
10. Unscrew screws and remove the protective panel of a wheel niche.
11. Unscrew bolts and remove a wing.
12. Installation is carried out upside-down.
13. Establish facing of an aperture of a wheel niche in the following order.
14. Remove with a scraper from lateral facing of a wing gluing tape.
15. Wipe a surface of facing covered with fat-free structure 3M ATD 8906.
16. Put to a facing bell new 2-сторонюю gluing tape 3M ATD 6382.
17. Heat up a tape surface till 40-60 ° With and remove a protective paper layer.
18. Establish facing on a wing so that latches came into openings, densely press facing.
19. Rivet facing in places of remote rivets (1 – the adaptation, 2 – the panel of a body and facing, 3 – a mortgage rivet).