Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
- 12. Body
   12.1. Maintenance and repair
   12.2. Vinyl furnish
   12.3. Upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repair of openings from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. Windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. Cover of a back compartment
   12.16. Bumpers
   12.17. Forward facing lattice
   12.18. External mirrors
   12.19. Forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. Hatch
   12.23. Holder of a spare wheel
   + 12.24. Salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. Ceiling upholstery
   12.28. Switch of the door lock
   + 12.29. Door glass, window regulator and window regulator electric motor
   12.30. Windscreen
   12.31. Back glass
   12.32. Vnutrisalonnoye rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. Electric equipment
+ 14. Electroschemes

12.28. Switch of the door lock


The door lock and the lobby handle (above) and a back door (on inserts – greasing places at assembly)

1. Button of blocking of the lock
2. Handle
3. Bracket
4. Lock switch
5. Lock mechanism
6, 7. Electric drive

The door lock and the handle of a back cover (1992-98) (on an insert – a greasing place at assembly)

1. Facing of a lamp of illumination
registration plate
2. Handle
3. Lock mechanism
4. Electric drive
5. Bracket
6. Lock switch

The door lock and the handle of a back cover (1992-98) (on an insert – a greasing place at assembly)

1. Internal panel and water filter
2. Arm
3. Facing
4. Handle external
5. Handle internal
6. Lock
7. Electric drive

Removal and installation


At dismantle of door locks the part of fastenings of drafts of the mechanism of a drive of the lock will be damaged, therefore for assembly prepare new fastenings (brackets, latches, etc.)

1. Lower glass and remove the internal panel of a door.
2. Carefully remove a windowpane sealant.
3. Remove brackets of fastening of drafts of the lock to the handle and a switch drum (on a part of cars it is recommended to disconnect drafts on the lock mechanism).
The switch of the lock which has been built in in the handle
4. Disconnect sockets of wires.
5. Unscrew nuts and remove the handle. It is necessary to remove the lock from the handle in a workshop with the qualified expert.
6. Installation is carried out upside-down.
The switch of the lock which has been built in at a door
7. Remove a podkovoobrazny bracket and remove a switch drum. Repair of the switch is under repair in a workshop the qualified expert.
8. Installation is carried out upside-down.
Switch of the lock of a back cover
9. Procedure differs nothing from described for door locks.