Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
- 12. Body
   12.1. Maintenance and repair
   12.2. Vinyl furnish
   12.3. Upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repair of openings from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. Windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. Cover of a back compartment
   12.16. Bumpers
   12.17. Forward facing lattice
   12.18. External mirrors
   12.19. Forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. Hatch
   12.23. Holder of a spare wheel
   + 12.24. Salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. Ceiling upholstery
   12.28. Switch of the door lock
   + 12.29. Door glass, window regulator and window regulator electric motor
   12.30. Windscreen
   12.31. Back glass
   12.32. Vnutrisalonnoye rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. Electric equipment
+ 14. Electroschemes






12.21. Body support (fastening to the chassis)

GENERAL INFORMATION

Design and details of support of a 4-door body (1992-95)

1, 2. Bolt
3, 8, 9. Washer
4. A support pillow from a body
5. Pillow And
6. Plug
7. A pillow In
10. Limiter
11. Samopodzhimny nut
12. Laying (to 1993)

Design and details of support of a 2-door body (1983-91)

N–at assembly is subject to replacement
1, 9. Bolt
2, 6. Washer
3. Pillow And
4. Plug
5. A pillow In
7. Samopodzhimny nut
8. Laying

Design and details of support of a 4-door body (1983-91)

N–at assembly is subject to replacement
1, 8. Bolt
2, 6. Washer
3. Pillow And
4. Plug
5. A pillow In
7. Samopodzhimny nut
9. Laying

If performance of any works it is necessary to remove bolts of fastening of a body, the body should be raised only on height at which access is provided, it is forbidden to lift a body on considerable height as breakages are possible.

If it is necessary to replace any fastening of a body, it is necessary to unscrew all bolts of fastening of a body on this party and to establish under a support body about each of fastenings.

PERFORMANCE ORDER
1. Lift the car, establish supports under each support, having laid wooden whetstones. At least one support establish under a frame.
2. Unscrew bolts of support of a body from that party on which work is carried out. At possibility remove a washer and the bottom pillow.
3. Clean a support from under frames and it is careful приопустите a frame from that party on which work is carried out, do not allow excessive lowering of a frame.
4. Again establish under a frame a support.
5. Remove the top pillow, the plug and laying.
6. Establish details of a support of a body upside-down.
7. Tighten nuts of support according to the demanded moments.