Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
- 11. Brake system
11.1. Technical characteristics
11.2. Vacuum amplifier of brakes
11.3. Adjustment of brakes
11.4. Switch of a signal of braking
11.5. Removal and pedal installation
11.6. Main cylinder of brakes
11.7. The dosing-out valve
11.8. Regulator of pressure of back brakes (1992-98)
11.9. Control valve of the amplifier of brakes
11.10. Hoses and tubes
11.11. Air removal from a hydraulic actuator of brakes
+ 11.12. Forward disk brakes
+ 11.13. Back drum-type brakes
+ 11.14. Back disk brakes (1992-98)
+ 11.15. Hand brake
11.16. Anti-blocking system (ABS)
11.17. Hydromodule
11.18. Overload sensor
11.19. Sensor of speed
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
Sensor of speed forward (above) and back wheel
|
|
On forward wheels
1. Sensitive element of the sensor
2. Arm
3. Rotor
On back wheels
4. Sensitive element of the sensor |
5. Sealant
6. Arm
7. Rotor
N–the detail at assembly is subject to replacement |
Check
| PERFORMANCE ORDER |
| 1. Remove the sensor and a gear rotor. |
| 2. At detection on a polar tip of the sensor of damages or a metal deposit owing to a magnetic attraction, the sensor replace. |
|
3. Check resistance between sensor conclusions. For sensors of forward wheels resistance should be 900–1100 Ohm, sensors of back wheels – 1300–2100 Ohm. |
|
4. Resistance of the sensor on the case should be not less than 100 kiloohms. |
| 5. Otherwise the sensor replace. |
| 6. The sensor with visible damages replace. |
|
7. Check a condition of teeths of a rotor. A rotor with the worn-out or broken teeths replace. |
|
Removal and installation
SENSORS OF FORWARD WHEELS
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight, lift the car and remove a wheel. |
| 2. Disconnect from the sensor the socket, remove brackets and get conducting. |
| 3. Unscrew 2 bolts on a rotary fist and it is careful, without allowing impact, remove a magnetic part of the sensor from a fist. |
| 4. Remove a conducting arm. |
| 5. Remove a nave with a disk (see subsection 9.3.12, subsection 9.3.13) and get a sensor rotor, having unscrewed bolts. |
| 6. Installation is carried out upside-down. |
|
7. Sustain a gap of 0,2-1,0 mm between a head of the sensor and a rotor wreath. In case of violation of this gap check correctness of installation of a rotor. |
| 8. If the sensor changed, check system in car-care center. |
|
SENSORS OF BACK WHEELS
| PERFORMANCE ORDER |
| 1. Disconnect the battery from weight, lift the car and remove a back wheel. |
| 2. Disconnect from the sensor the socket on the lever of a back suspension bracket, remove brackets on a beam of the bridge and get conducting. |
|
3. Unscrew 2 bolts on a board of a brake and carefully remove a sensitive element of the sensor and sealing rings. |
| 4. Remove a semi-axis (see subsection 9.4.1) and a brake disk, remove a rotor and a sensor arm. |
| 5. Installation is carried out upside-down. |
|
6. Sustain a gap of 0,3-0,9 mm between a head of the sensor and a rotor wreath. In case of violation of this gap check correctness of installation of a disk of a brake. |
| 7. If the sensor changed, check system in car-care center. |
|
|
|