Mitsubishi Pajero

1982-1998 of release

Repair and car operation

Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
- 11. Brake system
   11.1. Technical characteristics
   11.2. Vacuum amplifier of brakes
   11.3. Adjustment of brakes
   11.4. Switch of a signal of braking
   11.5. Removal and pedal installation
   11.6. Main cylinder of brakes
   11.7. The dosing-out valve
   11.8. Regulator of pressure of back brakes (1992-98)
   11.9. Control valve of the amplifier of brakes
   11.10. Hoses and tubes
   11.11. Air removal from a hydraulic actuator of brakes
   + 11.12. Forward disk brakes
   + 11.13. Back drum-type brakes
   - 11.14. Back disk brakes (1992-98)
      11.14.1. Replacement of blocks
      11.14.2. Brake support
      11.14.3. Disk of a back brake
   + 11.15. Hand brake
   11.16. Anti-blocking system (ABS)
   11.17. Hydromodule
   11.18. Overload sensor
   11.19. Sensor of speed
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes

11.14.2. Brake support

GENERAL INFORMATION

Brake support

Dismantling order
1. Finger bottom
2. Axis
3. Plug
4. Support assembled
5, 7. Cover
6. Ring
8. Piston
9. Sealant
10. Case

Order of removal of blocks
1. Finger bottom
2. Axis
3. Plug
4. Support assembled
11. Blocks with the indicator
12. Block
13. External plate
14. Bracket

Brake support (removal order)

1. Hose

2. Support assembled

3. Disk

Places of greasing of a support at assembly

1. In these cavities special greasing which it is impossible to delete is put.

The support should be removed on each wheel separately.

Removal and installation

PERFORMANCE ORDER

1. Lift a front of the car and remove a wheel.
2. Remove a part of liquid from a tank.
3. Disconnect on a support a brake hose, muffle openings.
4. Unscrew an axis and a finger and remove a support. It is possible to remove also a support assembled with an arm for what it is necessary to unscrew 2 bolts of fastening of an arm to a brake board.
5. Installation is carried out upside-down taking into account the following.
	6. Drown the piston in the cylinder.
7. Tighten connections with the next moments: bolts of fastening of an arm of a support (if acted in film) – 90 N of m, an axis and a finger of a support of 32-42 N of m (top), the hose union – 17 N of m.
8. Remove air from a hydraulic actuator.

Dismantling and assembly

PERFORMANCE ORDER

1. Remove a cover.
	2. Carefully remove pistons with the compressed air.
	3. Carefully get from the cylinder a cuff.
4. Check a condition of pistons and an internal surface of the cylinder.
5. At detection of corrosion and appreciable damages of a detail replace. In ремкомплект a support enter a sealant and the piston (it is delivered also separately), and also greasing for support fingers.
6. Assembly is carried out upside-down.
	7. At assembly establish an axis and the bottom finger on the places noted by letters of G and L (1 – a support axis, 2 – a finger, 3 – letters for the correct assembly).
8. Replace everything a sealant.
9. Grease a support and fingers. The piston grease with brake liquid.