Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
+ 9.1. Mechanical transmission
- 9.2. Coupling
9.2.1. Coupling adjustment
9.2.2. Coupling pedal
9.2.3. Details of a hummock drive of switching off of coupling
9.2.4. Coupling with a hydraulic actuator
9.2.5. Removal and coupling installation
9.2.6. Main cylinder of coupling
9.2.7. Working cylinder of switching off of coupling
9.2.8. Air removal from a coupling hydraulic actuator
+ 9.3. Automatic transmission
+ 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
Coupling pedal (hummock drive)
|
1. Switch socket
braking signal
2. Spring
3. Шплинт
4. Washer
5. Axis
6. Cable tip
7. Arm
8. Lever
9. Pedal
|
10. Axis of a pedal of a brake
11. Brake pedal
12. Signal switch
braking
13. Limiter bolt хоа
14. Plug
15. Шплинт
16. Cable
17. Plug
and. To grease |
Pedal couplings (hydraulic actuator), for and/m 1989-90 with the engine of 2,6 l
|
1. Spring
2. Rasshplintuyte fork axis
3. Washer
4. Fork axis
5. Arm
6. Axis
|
7. Pedal
8. Face plug
9. Axis plug
and. To grease
N–to replace at assembly |
Coupling pedal on and/m 1990-91, the engine of 3,0 l
|
1. Rasshplintuyte fork axis
2. Remove a spring
3. Arm
4. Шплинт
5. Plug
6. Bolt of the limiter of a course
7. Sensor of switching off of coupling
8. Шплинт
9. Washer
|
10. Fork axis
11. Bolt
12. Pedal
13. Face plug
14. Axis plug
15. Overlay of a pedal
and. To grease
N–to replace at assembly |
Coupling pedal on and/m 1992-95.
|
1. Rasshplintuyte fork axis
2. Disconnect the main cylinder that of an arm (one of nuts is from a motor compartment)
3. Pedal assembled
4. Fork axis
5. Earring And
6. Spring
7. An earring In
8. Plug
9. Pedal axis
10. Pedal
|
11. Face plug
12. Axis plug
13. Plugs
14. Slip
15. A bolt of the limiter of a course (on and/m without cruise control)
16. The sensor of inclusion of coupling (on and/m with system cruise control)
17. The blocking switch
18. Arm
and. To grease
N–to replace at assembly |
Removal and installation
CARS WITH THE HUMMOCK DRIVE OF COUPLING
| PERFORMANCE ORDER |
| 1. Release a nut of a cover of a cable that the weak point was formed. |
| 2. Disconnect a cable from a pedal. |
| 3. Unscrew a nut and remove the pedal lever, having designated its situation. |
| 4. Remove a pedal with an axis, having tracked safety of the plug of an axis. |
| 5. Installation is carried out upside-down. |
| 6. Grease necessary points. |
|
CARS WITH THE COUPLING HYDRAULIC ACTUATOR
Cars of 1989-90, engine of 2,6 l
Cars of 1990-91, engine of 3,0 l
Cars of 1992-98.
| PERFORMANCE ORDER |
| 1. A removal order (according to numbering of positions) coupling pedals on cars of 1992-98 look at fig. A coupling pedal on and/m 1992-95. |
| 2. At installation grease the specified places and tighten all connections according to the demanded moments. |
| 3. Adjust a pedal (see subsection 9.1.2). |
|
|
|