Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
- 12. Body
   12.1. Maintenance and repair
   12.2. Vinyl furnish
   12.3. Upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repair of openings from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. Windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. Cover of a back compartment
   12.16. Bumpers
   12.17. Forward facing lattice
   12.18. External mirrors
   12.19. Forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. Hatch
   12.23. Holder of a spare wheel
   + 12.24. Salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. Ceiling upholstery
   12.28. Switch of the door lock
   - 12.29. Door glass, window regulator and window regulator electric motor
      12.29.1. Cars of 1983-91.
      12.29.2. Cars of 1992-98.
   12.30. Windscreen
   12.31. Back glass
   12.32. Vnutrisalonnoye rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. Electric equipment
+ 14. Electroschemes






12.29. Door glass, window regulator and window regulator electric motor

12.29.1. Cars of 1983-91.

GENERAL INFORMATION

Window regulator of a forward door (1983-91)

1. Internal panel and water filter
2, 3. Uplotniteli
4. Safety lock
5. Window leaf
6. Holder
7. Lining
8. Glass
9. Window regulator

Glass of a back door (1983-91)

1. Internal panel and water filter
2, 3. Uplotniteli
4. Trenches
5. The central directing
6. Corner
7. Holder
8. Lining
9. Glass
10. Window regulator
* – treats cars with the window regulator electric drive

FORWARD DOOR

PERFORMANCE ORDER
1. Lower glass.
2. Remove the internal panel and the water filter.
3. Carefully hook and remove a glass sealant.
4. Remove a window safety lock, unscrew 3 bolts at doors (1 bolt in a forward part), holding a window leaf and remove a window leaf with a framework.
5. Unscrew bolts of holders and remove glass.
6. Unscrew window regulator bolts, disconnect electric motor wires.
7. Remove a window regulator, if necessary remove the electric motor.
8. Installation is carried out upside-down.
9. Tighten fastenings according to the demanded moments. Two bolts of fastening of a framework of a window leaf tighten with the moment of 6 N of m.
10. At installation of glass sustain the Y=76,5-77,5 sizes of mm and H=466,5-467,5 mm, at first having fixed the holder In (1), and then the holder And (2).
11. Adjust glass as follows.
12. Completely lift glass and release bolts and screws of fastening of glass and the back bottom directing.
13. Move glass, back directing and an auxiliary roller (if the window leaf is not provided) so that glass adjoined to a door framework on all perimeter.
14. Tighten bolts.

BACK DOOR

PERFORMANCE ORDER
1. Lower glass.
2. Remove the internal panel and the water filter.
3. Carefully hook and remove a glass sealant.
4. Carefully remove felt and rubber a trench.
5. Unscrew two screws in the top part of a window and two bolts of fastening central directing to a door and get directing, having submitted vertically up.
6. Remove a corner together with a sealant.
7. Remove the holder of glass from a window regulator and get glass.
8. Disconnect electric drive wires (if it is provided), unscrew bolts and remove a window regulator, if necessary remove the electric motor (previously remove a spring, otherwise after electric motor removal the window regulator can suddenly be straightened and put a trauma).
9. Installation is carried out upside-down taking into account the following.
10. The window regulator is established assembled with the electric motor, bolts of fastening tighten with the moment of 6 N of m.
11. Slightly grease a trench with universal greasing, excess of greasing is not allowed.
12. At installation of glass sustain the size of equal 231–239 mm.
13. If necessary adjust glass moving central directing at the released bolts.