Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
- 12. Body
   12.1. Maintenance and repair
   12.2. Vinyl furnish
   12.3. Upholstery and rugs
   12.4. Repair of small scratches
   12.5. Repair of dents
   12.6. Repair of openings from a rust or dents
   12.7. Filling and painting
   12.8. Repair of considerable damages
   12.9. Loops and locks
   12.10. Windscreen and motionless glasses
   12.11. Removal and installation of doors
   12.12. Door adjustment
   12.13. Removal and cowl installation
   12.14. Cowl adjustment
   12.15. Cover of a back compartment
   12.16. Bumpers
   12.17. Forward facing lattice
   12.18. External mirrors
   12.19. Forward aerial
   12.20. Removal and installation covered
   12.21. Body support (fastening to the chassis)
   12.22. Hatch
   12.23. Holder of a spare wheel
   + 12.24. Salon equipment
   12.25. Internal panels of doors
   12.26. Facing panels of salon
   12.27. Ceiling upholstery
   12.28. Switch of the door lock
   + 12.29. Door glass, window regulator and window regulator electric motor
   12.30. Windscreen
   12.31. Back glass
   12.32. Vnutrisalonnoye rear-view mirror
   + 12.33. Seats
   12.34. Seat belts
+ 13. Electric equipment
+ 14. Electroschemes






12.30. Windscreen

GENERAL INFORMATION

Windscreen

1, 2, 4, 6. Slips
3, 5. Latches
7. Glass
8. Lining

Places of drawing of a filler on a windscreen

1. Section on A-and
2. Section on V-in
3. From a body
4. Filler
5. Old glue
6. The bottom slip flew down
7. Sealant strip

With syringe put glue (type 3M Super Fast Urethane Auto Glass Sealant 8609 or equivalent) on all perimeter of glass.

Profile of drawing of a gluing layer in various sections on glass perimeter

1. Glue

2. Sealant strip

3. The bottom slip flew down

4. Section on A-and

5. Section on V-in


Removal

PERFORMANCE ORDER
1. The special tool remove lateral overlays of glass.
2. Remove latches.
3. On a part of cars get the bottom lining.
4. Paste over adjacent sites of a body with a tape made of cloth and a sharp drill drill an opening in a gluing layer of glass, pass a wire and cut off a layer.
5. Level the glue remains from a body otborkovka.
6. Designate the provision of glass and by means of special suckers get glass.

7. The broken latches replace (1 – a head, 2 – a latch of fastening of a windscreen)

Installation

PERFORMANCE ORDER
1. Put glue with a layer in thickness of 12-15 mm (on an insert the form of a cut of a submitting nozzle of a syringe which should be V-shaped is shown).
2. Paste a sealant.
3. Put glass in a place, outline a contour on glass edge.
4. Establish on glass the bottom slip.
5. With a sponge impregnated with a poliuretanovy filler (type 3М Super Fast Urethane Primer 8608 or equivalent) evenly put structure in demanded places.
6. Dry 3–30 minutes.
7. Again put glass in a place (the put contour) and slightly press.
8. Remove the glue which has got on glass or a body and wipe solvent 3М ATD 8906.
9. Wait for 30 mines for a glue skhvatyvaniye (drying can be accelerated a reflector, without allowing temperature increase over 100 ° C) and check seams on tightness, having watered with a weak stream from a hose.
10. Establish all removed details of facing.