Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
- 13. Electric equipment
   13.1. Detection of malfunctions in electric equipment system
   13.2. Tension check
   13.3. Detection of short circuit
   13.4. Check of reliability of grounding
   13.5. Check of integrity of a chain
   13.6. Finding of not closed chain
   13.7. Safety locks
   13.8. Burned-through crossing points
   13.9. Automatic switches
   13.10. System of safety of SRS (safety cushion)
   + 13.11. Heater
   - 13.12. Conditioner
      13.12.1. Compressor
      13.12.2. Condenser
      13.12.3. Condenser fan
      13.12.4. Auxiliary condenser and fan
      + 13.12.5. Evaporator
      13.12.6. Conditioner switch
      13.12.7. Conditioner control unit
      13.12.8. Broad valve
      13.12.9. Conditioner highway
      13.12.10. Ring sealant of tubes of a coolant
   + 13.13. Cruise control
   + 13.14. Audiosystem
   + 13.15. Cleaners of glasses
   + 13.16. Devices and switches
   + 13.17. Lighting devices
   + 13.18. Protection devices of electric chains
+ 14. Electroschemes






13.12.2. Condenser

GENERAL INFORMATION

Prevention

Assort condenser connections, without applying considerable efforts, tighten them without exceeding the set moment. At assembly replace sealing rings.


Removal and installation

CARS WITH ENGINES 2,6 AND 3,0 OF L (12-KLAPANNYE)

PERFORMANCE ORDER
1. Depressurize the coolant highway in car-care center.
One-stage conditioner
2. Remove a forward lattice.
3. Carefully turn on the union on the condenser. On V6 engines there are 3 connections on the right and 4 connections at the left. On the engine of 2,6 l disconnect the highway on the condenser and disconnect a moisture separator.
4. Unscrew bolts and remove a moisture separator.
5. Remove the condenser fan.
6. Unscrew a bolt and remove the condenser.
7. Installation is carried out upside-down.
8. The union tighten with the moment of 24 N of m.
The two-level conditioner (with 2 condensers in a cooling contour)
9. Remove a facing lattice of a front of the car.
10. Carefully turn on the union of tubes on condensers and from the opposite side, unscrew bolts and remove a moisture separator.
11. Remove the condenser fan.
12. Unscrew a bolt from the opposite side of a moisture separator and remove the condenser.
13. Disconnect the socket from the auxiliary fan, unscrew bolts and remove the second condenser.
14. Installation is carried out upside-down.
15. Replace sealing rings of unions.
16. The union tighten with the moment of 24 N of m.

CARS WITH ENGINES OF 3,0 L (24-KLAPANNYE) AND 3,5 L

PERFORMANCE ORDER
1. Depressurize the coolant highway in car-care center.
2. Disconnect the battery from weight.
3. Remove a facing lattice of a front of the car.
4. Remove an arm of the lock of a cowl.
5. Unscrew bolts of a cooler of transmission liquid.
6. Unscrew bolts of an oil radiator, remove an arm.
7. Unscrew bolts of fastening of the condenser.
8. Disconnect a tube of a high pressure on the condenser and a moisture separator.
9. Remove a moisture separator and an arm.
10. Remove the condenser fan.
11. Disconnect the top hose of a high pressure on the condenser.
12. Remove the condenser and get consolidations.
13. Installation is carried out upside-down.
14. Replace sealing rings of unions.
15. The union tighten with the moment of 24 N of m.