Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. Mechanism of management of transmission
      9.3.5. Epiploon of a shaft of a case of transmission
      9.3.6. Removal and transmission installation
      9.3.7. Transfer case
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward driveshaft and crosspieces
      + 9.3.10. Back driveshaft and crosspieces
      9.3.11. Forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semi-axes and epiploons of a forward axis
      9.3.15. Reducer of a forward axis
      9.3.16. Dismantling of CV JOINTS
   + 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.3.16. Dismantling of CV JOINTS

GENERAL INFORMATION

Details of the CV JOINT of the Double-offset type of the right semi-axis

1. Collar And
2. A collar In
3. Spring ring
4. External holder
6. Balls
7. Separator
8. Lock ring
9. Internal holder
10. Cover
11. Dustproof cover
12. Letna of the protective case of a cover
13. Protective case of a cover
14. Collar And
15. A collar In
16. Cover of the CV JOINT of the Bierfiild type

Details of the CV JOINT of the Double-offset type of the left semi-axis

1. Collar And
2. A collar In
3. Spring ring
4. External holder
5. Dustproof cover
6. Balls
7. Separator
8. Lock ring
9. Internal holder
10. Cover
11. Dustproof cover
12. Tape of the protective case of a cover
13. Protective case of a cover
14. Collar And
15. A collar In
16. Cover of the external CV JOINT of the Bieriild type
17. Semi-axis of the external CV JOINT of the Bieriild type
18. Spring ring

Assembly is carried out in
sequences (according to numbers of positions) 17–16–14–15–2–10–1–7–9–8–
– 6–5–4–3–18–13–12–11

Device of the CV JOINT of the Double-offset type

1. Separator

2. Lock ring

3. Internal holder


On considered cars folding CV JOINTS, – axial the DOJ (double-offset) or TJ (tripod) type, – c of inside and not folding, – BJ (Bierfiild type) or RJ (Rzeppa type), – from the outer side are established.

Regularly check a condition of covers of CV JOINTS, at the slightest visible damages covers immediately replace.

When dismantling CV JOINTS it is necessary to replace collars of covers and spring rings, keep in mind that these details are not interchangeable for models of different years of release and at their acquisition it is necessary to specify a code by the catalog.

PERFORMANCE ORDER
Tripod type CV JOINT
1. Remove big and small collars and remove a hinge cover, having displaced it on a semi-axis.
2. Carefully remove a hinge holder.
3. Remove a lock ring and remove a crosspiece, wash out it, but do not assort.
4. Remove a crosspiece, having wrapped up an insulating tape of a shlitsa of a semi-axis, and remove a cover.
5. Check a condition of details.
6. Collect and establish the hinge upside-down.
7. Grease a crosspiece with the greasing delivered in ремкомплекте.
Double-offset type CV JOINT
8. Dismantling assembly are carried out according to numbers of positions (see fig. Details of the CV JOINT of the Double-offset type of the left semi-axis).
9. When dismantling designate labels an initial relative positioning of a separator and an internal holder of the CV JOINT and a semi-axis which at assembly combine.
10. Grease a holder and a hinge separator with the greasing delivered in ремкомплекте, establish balls.
11. Fill an external holder with greasing approximately on 1/3, establish a lock ring and collect the CV JOINT. With the rest of greasing fill a reverse side of the hinge or a cover.

Replacement of covers of CV JOINTS

PERFORMANCE ORDER
1. The replacement procedure of a cover of the internal CV JOINT practically differs nothing from a dismantling order (see above).
2. The cover of the external CV JOINT acts in film after removal of the internal CV JOINT and removal of collars.
3. At assembly about 1/2 greasings put in the hinge and 1/2 – in a new cover.
4. Replace cover collars.