Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. Mechanism of management of transmission
      9.3.5. Epiploon of a shaft of a case of transmission
      9.3.6. Removal and transmission installation
      9.3.7. Transfer case
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward driveshaft and crosspieces
      + 9.3.10. Back driveshaft and crosspieces
      9.3.11. Forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semi-axes and epiploons of a forward axis
      9.3.15. Reducer of a forward axis
      9.3.16. Dismantling of CV JOINTS
   + 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.3.13. A nave with an automatic unblocking

GENERAL INFORMATION

Device of the mechanism of automatic blocking of a nave (1983-98)

1, 11. A brake In
2, 14, 21. Brake And
3, 12,27. Persistent ring And
4, 13, 26, 28. Cam
5, 15. Mobile gear wheel
6, 20. Leading gear wheel
7, 10. Case
8, 16. Shift spring
9, 17. Returnable spring
18, 23. The wheel is unblocked
19, 24. It is blocked
22. Uvula of a persistent ring And
25. A cam in gearing with a uvula of a persistent ring

Nave details with the mechanism of automatic blocking

1. Cap
2. Lock ring
3. Washer
4. Forward brake
5. Bolts
6. Blocking mechanism
7. Washer
8. Kontrovochny washer
9. Lock-nut
10. Forward nave

Details of the automatic mechanism of blocking of a nave

1. Cap
2. Ring
3. Case
4, 9. Cutting ring
5. A brake In
6. Brake And
7. Brake spring
8. Lock ring
10. Block of a leading gear wheel
11. Block of a mobile gear wheel
12. Returnable spring
13. Persistent plug B
14. Bearing
15. Lock ring of the leader
gear wheels
16. Persistent ring And
17. Leading gear wheel
18. Ring of a mobile gear wheel
19. Cam
20. Holder
21. Spring
22. Mobile gear wheel

Dismantling and assembly

PERFORMANCE ORDER
1. Unblock a nave for what transfer the lever of a transfer case to situation 2Н and hand over a backing on 1–2 m.
2. Remove forward wheels.
3. Remove a nave cap, if necessary release a cap a key for the oil filter, having wound it with rags.
4. Remove from a semi-axis a lock ring and remove a washer.
5. Unscrew 6 bolts and remove the unblocking mechanism.
6. With the flat thin tool remove a cutting ring, having wrung out a brake (In).
7. Remove a brake And, a brake In and a spring.
8. Remove a lock ring of the case of the mechanism.
9. By means of press Mv990811-01 slightly wring out a leading gear wheel and remove a cutting ring of the holder In (the course of a press should be not less than 40 mm, i.e. lengths of straightening of a spring, and the effort should not exceed 20 kgfs).
10. Slowly weaken pressure and remove the leader of gear wheels, a mobile gear wheel and a spring. Previously be convinced that a persistent ring Instead of залипло on the plug B.
11. Remove the persistent plug B and the bearing.
12. Remove a lock ring (is subject to replacement), remove a persistent ring And and a leading gear wheel.
13. Remove a lock ring of a mobile gear wheel. For this purpose wring out a cam and at the wrung-out spring remove a ring.
14. Further remove a cam, the holder of a spring, a spring and a mobile gear wheel.
15. Assembly is carried out upside-down taking into account the following.
16. Put in flutes of the persistent plug B and a brake In SAE J310А or NLGI N3 greasing.
17. Before installation of the assembled mechanism of blocking check by means of a dynamometer hooked for a hairpin of a wheel, effort of a provorachivaniye of a nave.
18. Grease places of contact of the case of the mechanism of blocking and a nave with hermetic 3M ART N 8661 or N 8663 or equivalent.
19. Establish the case, having combined a ledge on a brake In with a groove on a pin of a rotary fist (1 – a groove, 2 – a ledge, 3 – a brake In).
20. Tighten nave bolts with the moment of 50-60 N of m, and again measure effort of a provorachivaniye of a nave. The difference of efforts should not exceed 1 N of m, otherwise again disassemble and collect the blocking mechanism.
21. Tighten connections according to the demanded moments.
22. A cap tighten with the moment of 18-35 N of m.