Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   - 9.3. Automatic transmission
      9.3.1. Adjustments
      + 9.3.2. The blocking switch
      9.3.3. Check of adjustment of a cable of management by transmission
      9.3.4. Mechanism of management of transmission
      9.3.5. Epiploon of a shaft of a case of transmission
      9.3.6. Removal and transmission installation
      9.3.7. Transfer case
      9.3.8. Forward and back epiploons
      + 9.3.9. Forward driveshaft and crosspieces
      + 9.3.10. Back driveshaft and crosspieces
      9.3.11. Forward leading axis
      9.3.12. A nave with a manual unblocking
      9.3.13. A nave with an automatic unblocking
      9.3.14. Forward semi-axes and epiploons of a forward axis
      9.3.15. Reducer of a forward axis
      9.3.16. Dismantling of CV JOINTS
   + 9.4. Zadny Bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.3.1. Adjustments

GENERAL INFORMATION

CARS OF 1983-86.

Adjustment of inclusion of a kick-down-mode

Screw of adjustment of inclusion of a kick-down-mode (М904А)

The adjusting screw is on the left side of a transmission case.

1. To a cooler

2. Adjusting screw

PERFORMANCE ORDER
1. Unscrew a lock-nut on 5 turns.
2. Be convinced that the screw rotates without jammings.
3. Tighten the screw with the moment of 7,8 N of m.
4. Unscrew the screw on 3,5 turns, and, holding it, tighten a lock-nut with the moment of 40-55 N of m.

Adjustment of a tape of inclusion of a backing and the lowest transfer (low-reverse)

Screw of adjustment of inclusion of a backing and the lowest transfer

1. Screw

2. Lock-nut

PERFORMANCE ORDER
1. Lift the car.
2. Unscrew a lock-nut on 5 turns.
3. Be convinced that the screw rotates without jammings.
4. A key of MD998358 tighten the screw with the moment of 4,9 N of m.
5. Unscrew the screw on 7 turns, and, holding it, tighten a lock-nut with the moment of 34-47 N of m.
6. Establish the pallet and tighten bolts with the moment of 15-20 N of m.
7. Fill in liquid.

Kick-down-drive adjustment

CARS OF 1983-86.

Adjustment of system of drafts of a kick-down-mode (М904А)

1. Draft With

2. Bolt

3. Draft In

4. Control lever butterfly valve

5. Draft And

Check of turn of draft of management by a butterfly valve (after adjustment of other drafts)

1. Situation at completely open butterfly valve

2. Situation idling

3. Lever

PERFORMANCE ORDER
1. Release bolts so that drafts In and With freely moved.
2. Warm up the engine to 80 ° With and be convinced that fast idling is completely disconnected (a cam of the lever of an air zaslonka of the carburetor should not adjoin to a cam of the lever of a butterfly valve).
3. Submit draft And (or a control lever a butterfly valve) to the limiter of idling and establish drafts in the situation corresponding to idling.
4. Tighten a bolt connecting drafts In and Page.
5. Be convinced that when opening butterfly valve the lever on transmission turns on 47,5–54 °, and also that at slow return of draft of a butterfly valve from completely open provision of a zaslonka the lever on transmissions comes back to the situation corresponding to idling under the influence of a spring.

CARS OF 1987-89.

Adjustment of a kick-down-drive (КМ148)

1. Completely open zaslonka

2. Idling

3. Arm

PERFORMANCE ORDER
1. Believe idling turns (after adjustment of idling adjust a butterfly valve cable).
2. Check distance between the limiter of a cable and a cap which 52–53 mm should be at completely open zaslonka.
3. If necessary establish distance moving of an arm of a cable at the released bolts.

CARS OF 1990-98.

Adjustment of a gap of a cable of a kick-down-drive (and/m with engines of 3,5 l and 3,0 l 1990-94gg.)

1. Nuts

2. Cover

3. Cable limiter

Adjustment of a gap of a cable of a kick-down-drive (and/m with the engine of 3,0 l of 1995)

1. Nuts

2. Cable limiter

3. Cover

PERFORMANCE ORDER
Engine of 3,5 l and 3,0 l (1990-94)
1. Press a pedal of a butterfly valve and check distance between the limiter of a cable and a dustproof cover which should be 0–1 mm.
2. If necessary establish distance rotation of adjusting nuts of a cover of a cable.
Engine of 3,0 l (1995)
3. Remove a cover of a cable and and check distance between the limiter of a cable and a cover which 34–35 mm should be at completely open zaslonka.
4. If necessary establish distance rotation of adjusting nuts of a cover of a cable.