Mitsubishi Pajero

1982-1998 of release

Repair and car operation



Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
- 9. Running gear
   + 9.1. Mechanical transmission
   + 9.2. Coupling
   + 9.3. Automatic transmission
   - 9.4. Zadny Bridge
      9.4.1. Semi-axes, bearings and epiploons
      9.4.2. Adjustment axial люфта semi-axes
      9.4.3. Reducer of the back bridge
      9.4.4. Epiploon of a reducer of the back bridge
      9.4.5. Removal and installation of the back bridge
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes






9.4.5. Removal and installation of the back bridge

GENERAL INFORMATION

Zadny Bridge with springs

1. Drums
2. Bolts of fastening of a cable manual
brakes
3. Tip of a cable of the hand brake
4. Hose of brakes
5. Hose сапуна
6. Driveshaft
7. Shock-absorber
8. Step-ladders and buffer
9. Zadny Bridge

Zadny Bridge with springs and drum-type brakes

N–details are subject to replacement
1. Drums
2. Bolts of fastening of a cable
hand brake
3. Tip of a cable manual
brakes
4. Hose of brakes
5. Hose сапуна
6. Driveshaft
7. Stabilizer bolt
cross-section kstoychivost
8. Longitudinal bar
9. Cross-section bar
10. Bottom fastening of the shock-absorber
11. Zadny Bridge
12. Spring
13. Stabilizer of the cross-section
stability

Zadny Bridge with springs and disk brakes

N–details are subject to replacement
1. Support
2. Brake disk
3. Bolt of fastening of a cable manual
brakes (or sensor of speed)
4. Tip of a cable of the hand brake
5. Hose of brakes
6. Hose сапуна
7. An arm of a spring of the dosing-out valve
8. A hose of the blocked differential
9. Socket
10. Sensor of speed
11. Driveshaft
12. Bolt of fastening of the stabilizer of cross-section stability
13. Longitudinal bar
14. Cross-section bar
15. Bottom fastening of the shock-absorber
16. Zadny Bridge
17. Spring
18. Stabilizer of cross-section stability
* is a connection it is finally tightened after car lowering

THE BRIDGE WITH SPRINGS

PERFORMANCE ORDER
1. Lift the car and establish on supports, having rested them in a frame box.
2. Merge oil from a reducer.
3. Remove wheels and drums.
4. Disconnect a cable of the hand brake, remove a cable guard.
5. Disconnect a hose of a hydraulic actuator of brakes on a tee.
6. Disconnect a hose сапуна.
7. On a part of cars remove an arm of a spring of the dosing-out valve.
8. Put oriyentatsionny labels and disconnect the back driveshaft.
9. Raise the back bridge for an average part of a beam (or for beam pipes) and disconnect shock-absorbers.
10. Unscrew nuts and remove step-ladders with buffers.
11. Unscrew nuts, get back earrings and lower back parts of springs.
12. Working together, lower the bridge and get from under the car.
13. Installation is carried out upside-down.
14. Believe a condition of rubber plugs of an earring of a spring, if necessary replace.
15. Correctly сориентируйте a spring earring at assembly (1 – towards a reducer).
16. Nuts tighten finally after car lowering. Nuts and bolts tighten according to the demanded moments.
17. Remove air from a hydraulic actuator of brakes.

THE BRIDGE WITH SPRINGS

PERFORMANCE ORDER
1. Lift the car and establish on supports, having rested them in a frame box.
2. Merge oil from a reducer.
3. Remove wheels.
4. Remove drums (or a support and a brake disk, a support take aside and fix).
5. Disconnect a cable of the hand brake.
6. Disconnect a hose of a hydraulic actuator of brakes on a tee.
7. Disconnect a hose сапуна.
8. Remove an arm of the dosing-out valve of brakes.
9. On cars with the being self-blocked differential disconnect a hose and the conducting socket.
10. On cars with ABS system disconnect the sensor of speed.
11. Put on flanges oriyentatsionny labels and disconnect the back driveshaft.
12. Unscrew nuts of bolts of the stabilizer of cross-section stability, remove drafts of the stabilizer and the plug.
13. Raise the back bridge for an average part of a beam and disconnect longitudinal and cross-section bars.
14. Disconnect the bottom fastenings of shock-absorbers.
15. Lower the bridge, remove the stabilizer and springs.
16. Installation is carried out upside-down.
17. Establish tarelchaty washers on plugs of a bar of the back bridge in the necessary order.
18. Nuts and bolts tighten with the next moments: back fastening of a longitudinal bar of 122 N of m (drum-type brakes), 216–245 N of m (disk brakes), forward nuts tighten finally after car lowering with the moment of 150 N of m, nuts of a cross-section bar tighten after car lowering with the moment of 122 N of m (for drum-type brakes) and 230 N of m (disk brakes).
19. Nuts of back wheels tighten to the full before car lowering.
20. Other moments of an inhaling look at fig. Zadny Bridge with springs and drum-type brakes, Zadny Bridge with springs and disk brakes.
21. Remove air from a hydraulic actuator of brakes.