Mitsubisi Padzhero
+ 1.1. Dashboard and control units
+ 2. Maintenance
- 3. Engines
3.1. Candles
3.2. Check of wires
+ 3.3. Ignition system
- 3.4. Major maintenance of the engine
3.4.1. Engine electric equipment
3.4.2. Ignition distributor
+ 3.4.3. Generator
3.4.4. Battery
3.4.5. Starter
3.4.6. Traction relay of a starter
3.4.7. Sensors
+ 3.4.8. Instructions on service and engine repair
3.4.9. Compression check in cylinders of engines
3.4.10. Specifications of engines
+ 3.4.11. Removal and engine installation
3.4.12. Cover of a head of the block of cylinders
- 3.4.13. Rollers and yokes
3.4.13.1. Engine of 2,0 l
3.4.13.2. Engine of 2,6 l
3.4.13.3. Engines of 2,4 l and 3,0 l
3.4.13.4. Engine of 3,5 l
3.4.13.5. Diesel engine
3.4.14. Thermostat of system of cooling
3.4.15. Inlet collector
3.4.16. Final collector
3.4.17. The incorporated collector (a diesel engine with a turbo-supercharging)
3.4.18. Turbokompressor
3.4.19. Turbonagnetatel
3.4.20. Radiator
3.4.21. Maslookhladitel
3.4.22. Fan
3.4.23. The pump of cooling liquid
+ 3.4.24. Head of cylinders
3.4.25. Valves and springs
3.4.26. Saddles
3.4.27. Replacement of directing plugs
3.4.28. Hydropushers
+ 3.4.29. Gear belt and covers
3.4.30. Chain and cover (engine of 2,6 l)
3.4.31. Oil pallet
3.4.32. Oil pump and saylent-rollers (vibrogasitel)
3.4.33. Cam-shafts and support
3.4.34. Check of a condition of a cam-shaft
+ 3.4.35. Pistons and rods
3.4.36. Back epiploon
3.4.37. Radical bearings
3.4.38. Flywheel
+ 3.4.39. Exhaust system
+ 3.5. Diesel and turbodiesel engines 2,5 and 2,8 of l
+ 4. Cooling system
+ 5. Greasing system
+ 6. Power supply system
+ 7. Release system
+ 8. Fuel system
+ 9. Running gear
+ 10. Suspension bracket and steering
+ 11. Brake system
+ 12. Body
+ 13. Electric equipment
+ 14. Electroschemes
|
Removal
| PERFORMANCE ORDER |
| 1. Uncover heads of cylinders. |
| 2. Release a bolt of an asterisk of a cam-shaft. |
| 3. Establish the piston of the 1st cylinder in VMT, having turned the crankshaft before label combination on a crankshaft pulley with risky on a head of cylinders. Further rotation of the crankshaft is not allowed. |
| 4. Unscrew a bolt of an asterisk and get a small gear wheel of the distributor of ignition. |
| 5. Remove an asterisk with a chain and dress on the holder. |
| 6. Dress on hydropushers special brackets of MD998448. |
| 7. Gradually release bolts of covers of necks of a cam-shaft, having begun with the central bolt and being displaced on the periphery. |
| 8. Turn out bolts and get rollers with yokes. |
|
Installation
| PERFORMANCE ORDER |
| 1. Unscrew bolts of fastening of rollers on covers of basic necks and get covers, yokes, springs and washers. Store all removed details as their installation. |
| 2. Check a condition of persistent surfaces of yokes, both gaps in yokes and rollers. Check purity of oil channels. Worn-out details replace. Faulty pushers which do not provide complete closing of the valve, replace. For this purpose clean a bracket (the pusher will drop out) and insert a new pusher, having again fixed a bracket. |
| 3. Collect rollers with covers, having combined labels on rollers and on a forward cover. Grease and establish all removed details in a former order. |
| 4. Further assembly is carried out upside-down. Tighten bolts of fastening of rollers with the moment of 20 N of m. A bolt of an asterisk tighten with the moment of 54 N of m. Adjust the jet valve. |
|
|
|